ST72254G2-Auto STMicroelectronics, ST72254G2-Auto Datasheet - Page 96

• Manufacturer Part Number: ST72254G2-Auto
• Description: 8-bit MCU for automotive with single voltage Flash/ROM memory, ADC, 16-bit timers, SPI, I2C interfaces
• Manufacturer: STMicroelectronics

Specifications of ST72254G2-Auto

• Clock Sources: crystal/ceramic resonator oscillators or RC oscillators, external clock, backup Clock Security System
• 3 Power Saving Modes: Halt, Wait and Slow
• Two 16-bit Timers With: 2 input captures, 2 output compares, external clock input on one timer, PWM and Pulse generator modes (one only on ST72104Gx-Auto and ST72216G1- Auto)

ST72104Gx-Auto, ST72215Gx-Auto, ST72216Gx-Auto, ST72254Gx-Auto
13.2 ABSOLUTE MAXIMUM RATINGS
Stresses above those listed as “absolute maxi-
mum ratings” may cause permanent damage to
the device. This is a stress rating only and func-
tional operation of the device under these condi-
13.2.1 Voltage Characteristics
13.2.2 Current Characteristics
13.2.3 Thermal Characteristics
Notes:
1. Directly connecting the RESET and I/O pins to V
is generated or an unexpected change of the I/O configuration occurs (for example, due to a corrupted program counter).
To guarantee safe operation, this connection has to be done through a pull-up or pull-down resistor (typical: 4.7kΩ for
RESET, 10kΩ for I/Os). Unused I/O pins must be tied in the same way to V
2. When the current limitation is not possible, the V
I
3. All power (V
4. Negative injection disturbs the analog performance of the device. In particular, it induces leakage currents throughout
the device including the analog inputs. To avoid undesirable effects on the analog functions, care must be taken:
- Analog input pins must have a negative injection less than 0.8 mA (assuming that the impedance of the analog voltage
is lower than the specified limits)
- Pure digital pins must have a negative injection less than 1.6mA. In addition, it is recommended to inject the current as
far as possible from the analog input pins.
5. When several inputs are submitted to a current injection, the maximum ΣI
and negative injected currents (instantaneous values). These results are based on characterization with ΣI
mum current injection on four I/O port pins of the device.
6. True open drain I/O port pins do not accept positive injection.
96/135
INJ(PIN)
I
INJ(PIN)
ΣI
V
V
V
V
specification. A positive injection is induced by V
Symbol
Symbol
Symbol
ESD(HBM)
DD
INJ(PIN)
ESD(MM)
IN
T
I
I
VDD
VSS
I
STG
T
1) & 2)
IO
- V
J
2) & 4)
DD
SS
2)
) and ground (V
Total current into V
Total current out of V
Output current sunk by any standard I/O and control pin
Output current sunk by any high sink I/O pin
Output current source by any I/Os and control pin
Injected current on ISPSEL pin
Injected current on RESET pin
Injected current on OSC1 and OSC2 pins
Injected current on any other pin
Total injected current (sum of all I/O and control pins)
Supply voltage
Input voltage on true open drain pin
Input voltage on any other pin
Electrostatic discharge voltage (Human Body Model)
Electrostatic discharge voltage (Machine Model)
Storage temperature range
Maximum junction temperature
(see
Section 14.3 "THERMAL CHARACTERISTICS" on page
SS
) lines must always be connected to the external supply.
DD
SS
power lines (source)
Ratings
Ratings
Ratings
ground lines (sink)
DD
IN
or V
absolute maximum rating must be respected, otherwise refer to
IN
>V
SS
5) & 6)
DD
could damage the device if an unintentional internal reset
tions is not implied. Exposure to maximum rating
conditions for extended periods may affect device
reliability.
while a negative injection is induced by V
3)
3)
DD
or V
INJ(PIN)
SS
5)
according to their reset configuration.
see
trical Sensitivity" on page 112
is the absolute sum of the positive
V
Maximum value
SS
Maximum value
V
Section 13.7.2 "Absolute Elec-
128)
-0.3 to V
-65 to +150
SS
-0.3 to 6.5
Value
± 20
- 25
± 5
± 5
± 5
± 5
6.5
80
80
25
50
DD
+0.3
IN
INJ(PIN)
<V
SS
Unit
Unit
Unit
mA
°C
V
.
maxi-