IC PWR SUPPLY DDR 28-TQFN

MAX8632ETI+T

Manufacturer Part NumberMAX8632ETI+T
DescriptionIC PWR SUPPLY DDR 28-TQFN
ManufacturerMaxim Integrated Products
MAX8632ETI+T datasheet
 


Specifications of MAX8632ETI+T

ApplicationsController, DDRVoltage - Input2 ~ 28 V
Number Of Outputs1Voltage - Output1.8V, 2.5V, 0.7 ~ 5.5 V
Operating Temperature-40°C ~ 85°CMounting TypeSurface Mount
Package / Case28-TQFN Exposed PadOutput Voltage1.8 V, 2.5 V, 0.7 V to 5.5 V
Output Current15 AInput Voltage2 V to 28 V
Mounting StyleSMD/SMTMaximum Operating Temperature+ 85 C
Minimum Operating Temperature- 40 CLead Free Status / RoHS StatusLead free / RoHS Compliant
1
2
3
4
5
6
7
8
9
10
11
Page 11
12
Page 12
13
Page 13
14
Page 14
15
Page 15
16
Page 16
17
Page 17
18
Page 18
19
Page 19
20
Page 20
21
22
23
24
25
26
27
28
29
Page 15/29

Download datasheet (822Kb)Embed
PrevNext
Integrated DDR Power-Supply Solution for
Desktops, Notebooks, and Graphic Cards
TO PWM
CONTROLLER
(SEE FIGURE 1)
Figure 3. Adjustable Current-Limit Threshold
I
LOAD(MAX)
I
LIM(VAL) =
0
TIME
Figure 4. Valley Current-Limit Threshold
when OVP and shutdown discharge are disabled
(OVP/UVP = REF or GND) or forcing DL high when OVP
and shutdown discharge are enabled (OVP/UVP =
AV
or OPEN). See Table 3 for a detailed truth table
DD
for OVP/UVP and shutdown settings. When AV
above 4.25V, the controller activates the buck regulator
and initializes the internal soft-start.
The buck regulator’s internal soft-start allows a gradual
increase of the current-limit level during startup to
______________________________________________________________________________________
MAX8632
1.0V
LX
reduce the input surge currents. The MAX8632 divides
the soft-start period into five phases. During the first
phase, the controller limits the current limit to only 20%
I
PEAK
of the full current limit. If the output does not reach reg-
ulation within 425µs, soft-start enters the second phase,
and the current limit is increased by another 20%. This
process repeats until the maximum current limit is
I
LOAD
reached, after 1.7ms, or when the output reaches the
nominal regulation voltage, whichever occurs first.
Adding a capacitor in parallel with the external ILIM
resistors creates a continuously adjustable analog soft-
I
LIMIT
start function for the buck regulator’s output.
Soft-start in the LDO section can be realized by con-
(
LIR
)
necting a capacitor between the SS pin and ground.
1 -
x
I
LOAD
2
When VTT is turned off or placed in standby mode, or
during thermal shutdown of the LDOs, the SS capacitor
is discharged. When VTT is turned on or when the ther-
mal limit is removed, an internal 4µA (typ) current
charges the SS capacitor. The resulting ramp voltage
on SS linearly increases the current-limit comparator
threshold to the VTT output, until full current limit is
attained when SS reaches approximately 1.6V. This
lowering of the current limit during startup limits the ini-
tial inrush current peaks, particularly when driving
capacitors. Choose the value of the SS capacitor
appropriately to set the soft-start time window. Leave
rises
DD
SS floating to disable the soft-start feature.
POK1 is an open-drain output for a window comparator
that continuously monitors V
C
REF
REF
R
A
C
ILIM
ILIM
R
B
V
- 1V
DD
Power-OK (POK1)
. POK1 is actively held
OUT
15