C8051F020-TB Silicon Laboratories Inc, C8051F020-TB Datasheet - Page 247

• Manufacturer Part Number: C8051F020-TB
• Description: BOARD PROTOTYPING W/C8051F020
• Manufacturer: Silicon Laboratories Inc
• Type: MCUr

Specifications of C8051F020-TB

• Contents: Board
• Processor To Be Evaluated: C8051F02x
• Interface Type: USB
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant
• For Use With/related Products: C8051F020
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

Bit7:
Bit6:
Bit5:
Bit4:
Bit3:
Bit2:
Bit1:
Bit0:
TF4
R/W
Bit7
TF4: Timer 4 Overflow Flag.
Set by hardware when Timer 4 overflows. When the Timer 4 interrupt is enabled, setting this bit
causes the CPU to vector to the Timer 4 interrupt service routine. This bit is not automatically cleared
by hardware and must be cleared by software. TF4 will not be set when RCLK1 and/or TCLK1 are
logic 1.
EXF4: Timer 4 External Flag.
Set by hardware when either a capture or reload is caused by a high-to-low transition on the T4EX
input pin and EXEN4 is logic 1. When the Timer 4 interrupt is enabled, setting this bit causes the
CPU to vector to the Timer 4 Interrupt service routine. This bit is not automatically cleared by hard-
ware and must be cleared by software.
RCLK1: Receive Clock Flag for UART1.
Selects which timer is used for the UART1 receive clock in modes 1 or 3.
0: Timer 1 overflows used for receive clock.
1: Timer 4 overflows used for receive clock.
TCLK1: Transmit Clock Flag for UART1.
Selects which timer is used for the UART1 transmit clock in modes 1 or 3.
0: Timer 1 overflows used for transmit clock.
1: Timer 4 overflows used for transmit clock.
EXEN4: Timer 4 External Enable.
Enables high-to-low transitions on T4EX to trigger captures or reloads when Timer 4 is not operating
in Baud Rate Generator mode.
0: High-to-low transitions on T4EX ignored.
1: High-to-low transitions on T4EX cause a capture or reload.
TR4: Timer 4 Run Control.
This bit enables/disables Timer 4.
0: Timer 4 disabled.
1: Timer 4 enabled.
C/T4: Counter/Timer Select.
0: Timer Function: Timer 4 incremented by clock defined by T4M (CKCON.6).
1: Counter Function: Timer 4 incremented by high-to-low transitions on external input pin (T2).
CP/RL4: Capture/Reload Select.
This bit selects whether Timer 4 functions in capture or auto-reload mode. EXEN4 must be logic 1 for
high-to-low transitions on T4EX to be recognized and used to trigger captures or reloads. If RCLK1
or TCLK1 is set, this bit is ignored and Timer 4 will function in auto-reload mode.
0: Auto-reload on Timer 4 overflow or high-to-low transition at T4EX (EXEN4 = 1).
1: Capture on high-to-low transition at T4EX (EXEN4 = 1).
EXF4
R/W
Bit6
Figure 22.28. T4CON: Timer 4 Control Register
RCLK1
R/W
Bit5
TCLK1
R/W
Bit4
EXEN4
R/W
Bit3
Rev. 1.4
TR4
R/W
Bit2
C/T4
C8051F020/1/2/3
R/W
Bit1
CP/RL4
R/W
Bit0
SFR Address:
00000000
Reset Value
0xC9
247