AD9517-2/PCBZ Analog Devices Inc, AD9517-2/PCBZ Datasheet - Page 71

• Manufacturer Part Number: AD9517-2/PCBZ
• Description: BOARD EVAL FOR AD9517-2
• Manufacturer: Analog Devices Inc

Specifications of AD9517-2/PCBZ

• Main Purpose: Timing, Clock Generator
• Embedded: No
• Utilized Ic / Part: AD9517-2
• Primary Attributes: 2 Inputs, 12 Outputs, 2.2GHz VCO
• Secondary Attributes: CMOS, LVDS, LVPECL Output Logic, ADIsimCLK™ Graphical User Interface
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

Reg.
Addr.
(Hex)
0x143
Table 58. LVPECL Channel Dividers
Reg.
Addr.
(Hex)
0x190
0x191
0x192
0x196
0x197
Bits
[2:1]
0
Bits
[7:4]
[3:0]
7
6
5
4
[3:0]
1
0
[7:4]
[3:0]
7
6
5
Name
Divider 0 low cycles
Divider 0 high cycles
Divider 0 bypass
Divider 0 nosync
Divider 0 force high
Divider 0 start high
Divider 0 phase offset
Divider 0 direct to output
Divider 0 DCCOFF
Divider 1 low cycles
Divider 1 high cycles
Divider 1 bypass
Divider 1 nosync
Divider 1 force high
Name
OUT7 LVDS output current
OUT7 power-down
Description
Set output current level in LVDS mode. This has no effect in CMOS mode.
2
0
0
1
1
Power-down output (LVDS/CMOS).
0: power on (default).
1: power off.
Description
Number of clock cycles (minus 1) of the divider input during which divider output stays
low. A value of 0x0 means that the divider is low for one input clock cycle (default = 0x0).
Number of clock cycles (minus 1) of the divider input during which divider output stays
high. A value of 0x0 means that the divider is high for one input clock cycle (default = 0x0).
Bypass and power-down the divider; route input to divider output.
0: use divider.
1: bypass divider (default).
Nosync.
0: obey chip-level SYNC signal (default).
1: ignore chip-level SYNC signal.
Force divider output to high. This requires that nosync (Bit 6) also be set.
0: divider output forced to low (default).
1: divider output forced to high.
Selects clock output to start high or start low.
0: start low (default).
1: start high.
Phase offset (default = 0x0).
Connect OUT0 and OUT1 to Divider 0 or directly to VCO or CLK.
0: OUT0 and OUT1 are connected to Divider 0 (default).
1: If Register 0x1E1[1:0] = 10b, the VCO is routed directly to OUT0 and OUT1.
If Register 0x1E1[1:0] = 00b, the CLK is routed directly to OUT0 and OUT1.
If Register 0x1E1[1:0] = 01b, there is no effect.
Duty-cycle correction function.
0: enable duty-cycle correction (default).
1: disable duty-cycle correction.
Number of clock cycles of the divider input during which divider output stays low.
A value of 0x0 means that the divider is low for one input clock cycle (default = 0x0).
Number of clock cycles (minus 1) of the divider input during which divider output stays
high. A value of 0x0 means that the divider is high for one input clock cycle (default = 0x0).
Bypass and power-down the divider; route input to divider output.
0: use divider (default).
1: bypass divider.
Nosync.
0: obey chip-level SYNC signal (default).
1: ignore chip-level SYNC signal.
Force divider output to high. This requires that nosync (Bit 6) also be set.
0: divider output forced to low (default).
1: divider output forced to high.
1
0
1
0
1
Rev. B | Page 71 of 80
Current (mA)
1.75
3.5
5.25
7
Recommended Termination (Ω)
100
100 (default)
50
50
AD9517-2