MC908AP32CFAE Freescale Semiconductor, MC908AP32CFAE Datasheet - Page 201

• Manufacturer Part Number: MC908AP32CFAE
• Description: IC MCU 32K FLASH 8MHZ 48-LQFP
• Manufacturer: Freescale Semiconductor
• Series: HC08r

Specifications of MC908AP32CFAE

• Core Processor: HC08
• Core Size: 8-Bit
• Speed: 8MHz
• Connectivity: I²C, IRSCI, SCI, SPI
• Peripherals: LED, LVD, POR, PWM
• Number Of I /o: 32
• Program Memory Size: 32KB (32K x 8)
• Program Memory Type: FLASH
• Ram Size: 2K x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 5.5 V
• Data Converters: A/D 8x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 48-LQFP
• Controller Family/series: HC08
• No. Of I/o's: 32
• Ram Memory Size: 2KB
• Cpu Speed: 8MHz
• No. Of Timers: 2
• Embedded Interface Type: I2C, SCI, SPI
• Rohs Compliant: Yes
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -

RE — Receiver Enable Bit
RWU — Receiver Wakeup Bit
SBK — Send Break Bit
12.9.3 IRSCI Control Register 3
IRSCI control register 3:
Freescale Semiconductor
Setting this read/write bit enables the receiver. Clearing the RE bit disables the receiver but does not
affect receiver interrupt flag bits. Reset clears the RE bit.
This read/write bit puts the receiver in a standby state during which receiver interrupts are disabled.
The WAKE bit in IRSCC1 determines whether an idle input or an address mark brings the receiver out
of the standby state and clears the RWU bit. Reset clears the RWU bit.
Setting and then clearing this read/write bit transmits a break character followed by a logic 1. The logic
1 after the break character guarantees recognition of a valid start bit. If SBK remains set, the
transmitter continuously transmits break characters with no logic 1s between them. Reset clears the
SBK bit.
•
•
1 = Receiver enabled
0 = Receiver disabled
1 = Standby state
0 = Normal operation
1 = Transmit break characters
0 = No break characters being transmitted
Stores the ninth SCI data bit received and the ninth SCI data bit to be transmitted
Enables the following interrupts:
–
–
–
–
Receiver overrun interrupts
Noise error interrupts
Framing error interrupts
Parity error interrupts
Address:
Writing to the TE bit is not allowed when the enable SCI bit (ENSCI) is clear.
ENSCI is in SCI control register 1.
Writing to the RE bit is not allowed when the enable SCI bit (ENSCI) is
clear. ENSCI is in SCI control register 1.
Do not toggle the SBK bit immediately after setting the SCTE bit. Toggling
SBK before the preamble begins causes the SCI to send a break character
instead of a preamble.
Reset:
Read:
Write:
$0042
Bit 7
R8
U
Figure 12-14. IRSCI Control Register 3 (IRSCC3)
= Unimplemented
T8
U
6
MC68HC908AP Family Data Sheet, Rev. 4
DMARE
5
0
NOTE
NOTE
NOTE
DMATE
4
0
U = Unaffected
ORIE
3
0
NEIE
2
0
FEIE
1
0
PEIE
Bit 0
0
I/O Registers
201