ATMEGA16M1-AU Atmel, ATMEGA16M1-AU Datasheet - Page 290

• Manufacturer Part Number: ATMEGA16M1-AU
• Description: IC MCU AVR 16K FLASH 32TQFP
• Manufacturer: Atmel
• Series: AVR® ATmegar

Specifications of ATMEGA16M1-AU

• Core Processor: AVR
• Core Size: 8-Bit
• Speed: 16MHz
• Connectivity: CAN, LIN, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, POR, PWM, Temp Sensor, WDT
• Program Memory Size: 16KB (8K x 16)
• Program Memory Type: FLASH
• Eeprom Size: 512 x 8
• Ram Size: 1K x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 5.5 V
• Data Converters: A/D 11x10b; D/A 1x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 32-TQFP, 32-VQFP
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Number Of I /o: -

27.3.1
290
ATmega16M1/32M1/64M1
Latching of Fuses
Table 27-6.
Note:
.
Table 27-7.
Notes:
The status of the Fuse bits is not affected by Chip Erase. Note that the Fuse bits are locked if
Lock bit1 (LB1) is programmed. Program the Fuse bits before programming the Lock bits.
The fuse values are latched when the device enters programming mode and changes of the
fuse values will have no effect until the part leaves Programming mode. This does not apply to
the EESAVE Fuse which will take effect once it is programmed. The fuses are also latched on
Power-up in Normal mode.
High Fuse Byte
RSTDISBL
DWEN
SPIEN
WDTON
EESAVE
BOOTSZ1
BOOTSZ0
BOOTRST
Low Fuse Byte
CKDIV8
CKOUT
SUT1
SUT0
CKSEL3
CKSEL2
CKSEL1
CKSEL0
(2)
1. See
2. The SPIEN Fuse is not accessible in serial programming mode
3. See
4. The default value of BOOTSZ1..0 results in maximum Boot Size. See
1. The default value of SUT1..0 results in maximum start-up time for the default clock source.
2. The default setting of CKSEL3..0 results in internal RC Oscillator @ 8MHz. See
3. The CKOUT Fuse allows the system clock to be output on PORTB0. See
4. See
(3)
(4)
(3)
(1)
292
See
page 33
on page 33
Fuse High Byte
Fuse Low Byte
for details
“Alternate Functions of Port C” on page 74
“Watchdog Timer Configuration” on page 51
Table 8-9 on page 33
“System Clock Prescaler” on page 34
for details
Bit No
Bit No
7
6
5
4
3
0
7
6
5
4
3
2
0
for details
2
1
1
Description
External Reset Disable
debugWIRE Enable
Enable Serial Program and Data Downloading
Watchdog Timer Always On
EEPROM memory is preserved through the
Chip Erase
Select Boot Size (see Table 113 for details)
Select Boot Size (see Table 113 for details)
Select Reset Vector
Description
Divide clock by 8
Clock output
Select start-up time
Select start-up time
Select Clock source
Select Clock source
Select Clock source
Select Clock source
for details
for details
for description of RSTDISBL Fuse
for details
Default Value
1 (unprogrammed)
1 (unprogrammed)
0 (programmed, SPI
programming enabled)
1 (unprogrammed)
1 (unprogrammed),
EEPROM not reserved
0 (programmed)
0 (programmed)
1 (unprogrammed)
Default Value
0 (programmed)
1 (unprogrammed)
1 (unprogrammed)
0 (programmed)
0 (programmed)
0 (programmed)
1 (unprogrammed)
0 (programmed)
Table 27-11 on page
“Clock Output Buffer”
8209D–AVR–11/10
Table 8-9 on
(4)
(4)
(1)
(2)
(2)
(2)
(1)
(2)