ADUC7032BSTZ-8V-RL Analog Devices Inc, ADUC7032BSTZ-8V-RL Datasheet - Page 112
![IC BATTERY SENSOR PREC 48-LQFP](/photos/6/59/65923/505-48-lqfp_sml.jpg)
ADUC7032BSTZ-8V-RL
Manufacturer Part Number
ADUC7032BSTZ-8V-RL
Description
IC BATTERY SENSOR PREC 48-LQFP
Manufacturer
Analog Devices Inc
Series
MicroConverter® ADuC7xxxr
Datasheet
1.ADUC7032BSTZ-8V-RL.pdf
(128 pages)
Specifications of ADUC7032BSTZ-8V-RL
Core Processor
ARM7
Core Size
16/32-Bit
Speed
20.48MHz
Connectivity
LIN, SPI, UART/USART
Peripherals
POR, PSM, Temp Sensor, WDT
Number Of I /o
9
Program Memory Size
96KB (96K x 8)
Program Memory Type
FLASH
Ram Size
6K x 8
Voltage - Supply (vcc/vdd)
3.5 V ~ 18 V
Data Converters
A/D 2x16b
Oscillator Type
Internal
Operating Temperature
-40°C ~ 105°C
Package / Case
48-LQFP
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Eeprom Size
-
Other names
ADUC7032BSTZ-8V-RLCT
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
ADUC7032BSTZ-8V-RL
Manufacturer:
Analog Devices Inc
Quantity:
10 000
Preliminary Technical Data
SERIAL PERIPHERAL INTERFACE
The ADuC7032 features a complete hardware Serial Peripheral
Interface (SPI) on-chip. SPI is an industry standard
synchronous serial interface which allows eight bits of data to
be synchronously transmitted and received simultaneously, i.e.,
full duplex.
The SPI interface is only operational with core clock divider bits
(POWCON[2:0]= 0 or 1).
The SPI Port can be configured for Master or Slave operation
and consists of four pins, which are multiplexed with four
GPIO. The four SPI pins are MISO, MOSI, SCLK and SS . The
pins to which this signals are connected are shown in Table 77.
Pin
GP0 ( GPIO MODE 1 )
GP1 ( GPIO MODE 1 )
GP2 ( GPIO MODE 1 )
GP3 ( GPIO MODE 1 )
These signals are described in detail below.
MISO (Master In, Slave Out Data I/O Pin)
The MISO (master in slave out) pin is configured as an input
line in master mode and an output line in slave mode. The
MISO line on the master (data in) should be connected to the
MISO line in the slave device (data out). The data is transferred
as byte wide (8-bit) serial data, MSB first.
MOSI (Master Out, Slave In Pin)
The MOSI (master out slave in) pin is configured as an output
line in master mode and an input line in slave mode.
The MOSI line on the master (data out) should be connected to
the MOSI line in the slave device (data in). The data is
transferred as byte wide (8-bit) serial data, MSB first.
SCLK (Serial Clock I/O Pin)
The master serial clock (SCLK) is used to synchronize the data
being transmitted and received through the MOSI SCLK
period. Therefore, a byte is transmitted/received after eight
SCLK periods. The SCLK pin is configured as an output in
master mode and as an input in slave mode.
In master mode polarity and phase of the clock are controlled
by the SPICON register, and the bit-rate is defined in the
Table 77 : SPI Output Pins
Signal
SS
SCLK
MISO
MOSI
Description
Chip Select
Serial Clock
Master Out, Slave In
Master In, Slave Out
Rev. PrD | Page 112 of 128
SPIDIV register as follow:
The maximum speed of the SPI clock is dependant on the clock
divider bits and is summarized in Table 78.
In slave mode, the SPICON register must be configured with
the phase and polarity of the expected input clock. The slave
accepts data from an external master up to 5.12 Mb at CD = 0.
The formula to determine the maximum speed is as follow:
In both master and slave modes, data is transmitted on one edge
of the SCL signal and sampled on the other. Therefore, it is
important that the polarity and phase are configured the same
for the master and slave devices.
Chip Select (SS ) Input Pin
In SPI Slave Mode, a transfer is initiated by the assertion of SS
which is an active low input signal. The SPI port will then
transmit and receive 8-bit data until the transfer is concluded by
de-assertion of SS . In slave mode SS is always an input.
SPI registers definition
The following MMR registers are used to control the SPI
interface:
- SPICON: 16-bit control register
- SPISTA: 8-bit read only status register
- SPIDIV: 8-bit serial clock divider register
- SPITX: 8-bit write only transmit register
- SPIRX: 8-bit read only receive register
Table 78: SPI speed vs. clock divider bits in master mode
CD bits
SPIDIV
Max SCLK (MHz)
Equation 4 : Maximum Receive Baud Rate
f
Equation 3 : SPI Baud Rate Calculation
serialcloc
k
f
=
serialcloc
2
×
20
1 (
k
.
+
48
=
SPIDIV
0
0x05
1.667
MHz
f
HCLK
4
ADuC7032
1
0x0B
0.833
)