ADUC7032BSTZ-8V-RL Analog Devices Inc, ADUC7032BSTZ-8V-RL Datasheet - Page 55
![IC BATTERY SENSOR PREC 48-LQFP](/photos/6/59/65923/505-48-lqfp_sml.jpg)
ADUC7032BSTZ-8V-RL
Manufacturer Part Number
ADUC7032BSTZ-8V-RL
Description
IC BATTERY SENSOR PREC 48-LQFP
Manufacturer
Analog Devices Inc
Series
MicroConverter® ADuC7xxxr
Datasheet
1.ADUC7032BSTZ-8V-RL.pdf
(128 pages)
Specifications of ADUC7032BSTZ-8V-RL
Core Processor
ARM7
Core Size
16/32-Bit
Speed
20.48MHz
Connectivity
LIN, SPI, UART/USART
Peripherals
POR, PSM, Temp Sensor, WDT
Number Of I /o
9
Program Memory Size
96KB (96K x 8)
Program Memory Type
FLASH
Ram Size
6K x 8
Voltage - Supply (vcc/vdd)
3.5 V ~ 18 V
Data Converters
A/D 2x16b
Oscillator Type
Internal
Operating Temperature
-40°C ~ 105°C
Package / Case
48-LQFP
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Eeprom Size
-
Other names
ADUC7032BSTZ-8V-RLCT
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
ADUC7032BSTZ-8V-RL
Manufacturer:
Analog Devices Inc
Quantity:
10 000
Preliminary Technical Data
ADC Filter Register :
Name :
Address :
Default Value :
Access :
Function :
Note:
Bit
15
14
13 - 8
7
6 – 0
Description
Chop enable
Set by user to enable system chopping of all active ADCs. When this bit is set the ADC will have very low offset errors and
drift but the ADC output rate will be reduced by a factor of 3 if AF=0 (see Sinc3 Decimation Factor bits below). If AF ≠ 0,
then ADC output update rate will be the same with chop on or off. When chop is enabled, the settling time is 2 output
periods.
Note: Should only be used with SF > 1
Running Average
Set by user to enable a running average by 2 function reducing ADC noise. This function is automatically enabled when
chopping is active. It is an optional feature when chopping is inactive and if enabled (when chopping is inactive) does
not reduce ADC output rate but will increase the settling time by 1 conversion period.
Cleared by user to disable the running average function.
Averaging Factor ( AF )
The value written to these bits is use to implement a programmable 1
further reduce ADC noise at the expense of output rate as described in Sinc Decimation Factor bits below.
Sinc3 Modify
Set by user to modify the standard Sinc3 frequency response to increase the filter stopband rejection by 5dBs approx.
This is achieved by inserting a second notch (NOTCH2) at F
notch in the response.
Sinc3 Decimation Factor (SF)
The value (SF) written in these bits controls the over sampling (decimation factor) of the Sinc3 filter. The output rate from
the Sinc3 filter is given by
F
For information on calculating the F
Note:
ADC
- In low power mode and low power-plus mode, the ADC is driven directly by the low power oscillator (131KHz) and
not 512KHz. All F
- For optimal ADC performance, SF should be increased before AF is used.
- Due to limitations on the digital filter internal data-path, there are some limitations on the combinations of SF(Sinc3
Decimation Factor) and AF(Averaging Factor) that can be used to generate a required ADC output rate. This
restriction limits the minimum ADC update in Normal Power Mode to 4Hz or 1Hz in Low Power Mode. If all three ADCs
are enabled, then the minimum value of SF written by user code must be 1
= ( 512,000 / ( [SF+1] X 64 )) Hz when the CHOP bit (bit#15 above) = 0 and AF=0 (note AF = Averaging Factor)
Note : this is valid for all SF values <= 125
For SF= 126, F
For SF= 127, F
ADCFLT
0xFFFF0518
0x0007
Read/Write
The ADC Filter MMR is an 16-bit register that controls the speed and resolution of the on-chip ADCs.
If ADCFLT is modified, the Current, Voltage and Temperature ADCs are reset. An additional time of 60us per
enabled ADC is required before the first ADC result is available.
ADC
ADC
ADC
calculations should be divided by 4 (approx).
is forced to 60Hz
is forced to 50Hz
ADC
for SF ( other than 126 and 127 ) and AF values please refer to Table 28.
Table 27 : ADCFLT MMR Bit Designations
Rev. PrD | Page 55 of 128
NOTCH2
= 1.333 * F
st
order Sinc post filter. The averaging factor can
NOTCH
where F
NOTCH
is the location of the 1
ADuC7032
st