ATMEGA128RFA1-ZU Atmel, ATMEGA128RFA1-ZU Datasheet - Page 376

• Manufacturer Part Number: ATMEGA128RFA1-ZU
• Description: IC AVR MCU 2.4GHZ XCEIVER 64QFN
• Manufacturer: Atmel
• Series: ATMEGAr

Specifications of ATMEGA128RFA1-ZU

• Frequency: 2.4GHz
• Data Rate - Maximum: 2Mbps
• Modulation Or Protocol: 802.15.4 Zigbee
• Applications: General Purpose
• Power - Output: 3.5dBm
• Sensitivity: -100dBm
• Voltage - Supply: 1.8 V ~ 3.6 V
• Current - Receiving: 12.5mA
• Current - Transmitting: 14.5mA
• Data Interface: PCB, Surface Mount
• Memory Size: 128kB Flash, 4kB EEPROM, 16kB RAM
• Antenna Connector: PCB, Surface Mount
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 64-VFQFN, Exposed Pad
• Rf Ic Case Style: QFN
• No. Of Pins: 64
• Supply Voltage Range: 1.8V To 3.6V
• Operating Temperature Range: -40°C To +85°C
• Svhc: No SVHC (15-Dec-2010)
• Rohs Compliant: Yes
• Processor Series: ATMEGA128x
• Core: AVR8
• Data Bus Width: 8 bit
• Program Memory Type: Flash
• Program Memory Size: 128 KB
• Data Ram Size: 16 KB
• Interface Type: JTAG
• Maximum Clock Frequency: 16 MHz
• Number Of Programmable I/os: 38
• Number Of Timers: 6
• Operating Supply Voltage: 1.8 V to 3.6 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: EWAVR, EWAVR-BL
• Development Tools By Supplier: ATAVR128RFA1-EK1
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

Rev. 2467H-02/03
Rev. 2467G-09/02
Rev. 2467F-09/02
376
ATmega128
7. Updated R
8. Added a proposal for solving problems regarding the JTAG instruction IDCODE in
1. Corrected the names of the two Prescaler bits in the SFIOR Register.
2. Added Chip Erase as a first step under
3. Removed reference to the “Multipurpose Oscillator” application note and the “32kHz
4. Corrected OCn waveforms in
5. Various minor Timer1 corrections.
6. Added information about PWM symmetry for Timer0 and Timer2.
7. Various minor TWI corrections.
8. Added reference to
9. Added note under
10. Removed ADHSM completely.
11. Added section
12. Updated drawings in
1. Changed the Endurance on the Flash to 10,000 Write/Erase Cycles.
1. Added 64-pad QFN/MLF Package and updated
2. Added the section
3. Added the section
4. Renamed SPMCR to SPMCSR in entire document.
5. When using external clock there are some limitations regards to change of frequency.
6. Added a sub section regarding OCD-system and power consumption in the section
7. Corrected typo (WGM-bit setting) for:
“Errata” on page
“Programming the EEPROM” on page
Crystal Oscillator” application note, which do not exist.
Programming to inform about the Flash Page size.
writing to the EEPROM during an SPM Page load.
on page
This is descried in
Drive,” on page
“Minimizing Power Consumption” on page
“Fast PWM Mode” on page 98
32.
PU
values in
“EEPROM Write During Power-down Sleep Mode” on page
320.
371.
“Default Clock Source” on page
“Filling the Temporary Buffer (Page Loading)” on page 280
“Using all Locations of External Memory Smaller than 64 Kbyte”
Table 124 on page 291
“External Clock” on page 42
“Packaging Information” on page
“DC Characteristics” on page
(Timer/Counter0).
Figure 52 on page
316.
“Programming the Flash” on page 315
from both SPI Serial Programming and Self
47.
“Ordering Information” on page
125.
37.
and
318.
369.
Table 131, “External Clock
2467V–AVR–02/11
24.
368.
about
and