EP9315-IBZ Cirrus Logic Inc, EP9315-IBZ Datasheet - Page 425

• Manufacturer Part Number: EP9315-IBZ
• Description: 32-Bit Microcontroller IC
• Manufacturer: Cirrus Logic Inc
• Series: EP9r

Specifications of EP9315-IBZ

• Controller Family/series: (ARM9)
• Core Size: 32 Bit
• A/d Converter: 12 Bits
• Supply Voltage: 3.3V
• No. Of I/o Pins: 65
• Package / Case: 352-PBGA
• Clock Frequency: 200MHz
• Core Processor: ARM9
• Speed: 200MHz
• Connectivity: EBI/EMI, EIDE, Ethernet, I²C, IrDA, Keypad/Touchscreen, PCMCIA, SPI, UART/USART, USB
• Peripherals: AC'97, DMA, I&sup2:S, LCD, LED, MaverickKey, POR, PWM, WDT
• Number Of I /o: 16
• Program Memory Type: ROMless
• Ram Size: 32K x 8
• Voltage - Supply (vcc/vdd): 1.65 V ~ 3.6 V
• Data Converters: A/D 8x12b
• Oscillator Type: External
• Operating Temperature: -40°C ~ 85°C
• Processor Series: EP93xx
• Core: ARM920T
• Data Bus Width: 32 bit
• 3rd Party Development Tools: MDK-ARM, RL-ARM, ULINK2
• Development Tools By Supplier: EDB9315A-Z
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: 598-1144 - KIT DEVELOPMENT EP9315 ARM9
• Eeprom Size: -
• Program Memory Size: -
• Lead Free Status / Rohs Status: Details
• Other names: 598-1263

CONTROL
DS785UM1
ETDP
31
15
Address:
Definition:
Bit Descriptions:
30
14
TM
Channel Base Address + 0x002C
Channel Base Address + 0x003C
Channel Base Address + 0x0028
Channel Base Address + 0x0030
Channel Base Address + 0x0034
Channel Base Address + 0x0038
29
13
PWSC
SAH
28
12
Channel Base Address + 0x0000 - Read/Write
This is the Channel Control Register. Used to configure the DMA M2M
Channel. All control bits should be programmed before the ENABLE bit is set.
RSVD:
STALLIntEn:
SCT:
Offset
DAH
27
11
Note:See
Note:* Write this location once to clear the bit (see Interrupt/Status register description
Table 10-8. PPALLOC Register Reset Values (Continued)
26
10
for which bits this rule applies to).
PW
Table 10-3
25
9
Copyright 2007 Cirrus Logic
NO_HDSK
Reserved. Unknown During Read.
Setting this bit to “1” enables the generation of the STALL
interrupt in the STALL State of the DMA Channel State
machine. Setting this bit to “0” disables generation of the
STALL Interrupt.
Source Copy Transfer. This bit is used to set up a block
transfer from 1 memory source location. If SCT = 1, then
one word is read from the source memory location and
copied to a block of memory (the number of destination
locations written to is determined by BCR). If SCT = 0 then
the source address increments as normal after each
successful transfer as determined by the transfer size (this
is the default setting). In order to use this feature the
SAR_BASEx and DAR_BASEx registers must contain
word-aligned addresses - the DMA will ignore the 2 LSB’s
SAR_CURRENT1
DAR_CURRENT0
DAR_CURRENT1
24
for Channel Base Addresses
8
DAR_BASE0
DAR_BASE1
Reserved
Name
23
7
BWC
RSS
22
6
NFBintEn
Access
21
5
R/W
R/W
RO
RO
RO
START
20
4
DREQP
Bits
32
32
32
32
32
ENABLE
19
3
Reset Value
DONEIntEn
RSVD
18
0
0
0
0
0
EP93xx User’s Guide
2
DMA Controller
DACKP
SCT
17
1
STALLIntEn
ETDP
16
10-31
0
10