NH82801HEM S LB9B Intel, NH82801HEM S LB9B Datasheet - Page 578
![no-image](/images/manufacturer_photos/0/3/336/intel_sml.jpg)
NH82801HEM S LB9B
Manufacturer Part Number
NH82801HEM S LB9B
Description
Manufacturer
Intel
Datasheet
1.NH82801HEM_S_LB9B.pdf
(890 pages)
Specifications of NH82801HEM S LB9B
Lead Free Status / RoHS Status
Compliant
- Current page: 578 of 890
- Download datasheet (7Mb)
Table 132.
578
Run/Stop, Debug Bit Interaction SWDBG (Bit 5), Run/Stop (Bit 0) Operation
When the USB host controller is in Software Debug Mode (USBCMD Register bit 5=1),
the single stepping software debug operation is as follows:
To Enter Software Debug Mode:
In Software Debug mode, when the Run/Stop bit is set, the host controller starts.
When a valid TD is found, the Run/Stop bit is reset. When the TD is finished, the
HCHalted bit in the USBSTS register (bit 5) is set.
The SW Debug mode skips over inactive TDs and only halts after an active TD has been
executed. When the last active TD in a frame has been executed, the host controller
waits until the next SOF is sent and then fetches the first TD of the next frame before
halting.
10. HCD sets Run/Stop bit to 1 to resume normal schedule execution.
1. HCD puts host controller in Stop state by setting the Run/Stop bit to 0.
2. HCD puts host controller in Debug Mode by setting the SWDBG bit to 1.
3. HCD sets up the correct command list and Start Of Frame value for starting point in
4. HCD sets Run/Stop bit to 1.
5. Host controller executes next active TD, sets Run/Stop bit to 0, and stops.
6. HCD reads the USBCMD register to check if the single step execution is completed
7. HCD checks results of TD execution. Go to step 4 to execute next TD or step 8 to
8. HCD ends Software Debug mode by setting SWDBG bit to 0.
9. HCD sets up normal command list and Frame List table.
SWDBG
(Bit 5)
the Frame List Single Step Loop.
(HCHalted=1).
end Software Debug mode.
0
0
1
1
Run/Stop
(Bit 0)
0
1
0
1
If executing a command, the host controller completes the command
and then stops. The 1.0 ms frame counter is reset and command list
execution resumes from start of frame using the frame list pointer
selected by the current value in the FRNUM register. (While Run/
Stop=0, the FRNUM register (BASE + 06h) can be reprogrammed).
Execution of the command list resumes from Start Of Frame using the
frame list pointer selected by the current value in the FRNUM register.
The host controller remains running until the Run/Stop bit is cleared
(by software or hardware).
If executing a command, the host controller completes the command
and then stops and the 1.0 ms frame counter is frozen at its current
value. All status are preserved. The host controller begins execution
of the command list from where it left off when the Run/Stop bit is
set.
Execution of the command list resumes from where the previous
execution stopped. The Run/Stop bit is set to 0 by the host controller
when a TD is being fetched. This causes the host controller to stop
again after the execution of the TD (single step). When the host
controller has completed execution, the HC Halted bit in the Status
Register is set.
Description
UHCI Controllers Registers
Intel
®
ICH8 Family Datasheet
Related parts for NH82801HEM S LB9B
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
![NH82801HEM S LA5R](/images/manufacturer_photos/0/3/336/intel_tmb.jpg)
Part Number:
Description:
Manufacturer:
Intel
Datasheet:
![RJ80535VC600512](/images/manufacturer_photos/0/3/337/intel_corporation_tmb.jpg)
Part Number:
Description:
Microprocessor: Intel Celeron M Processor 320 and Ultra Low Voltage Intel Celeron M Processor at 600MHz
Manufacturer:
Intel Corporation
![82550GY](/images/manufacturer_photos/0/3/337/intel_corporation_tmb.jpg)
Part Number:
Description:
Intel 82550 Fast Ethernet Multifunction PCI/CardBus Controller
Manufacturer:
Intel Corporation
Datasheet:
![DA28F320J5-120](/images/manufacturer_photos/0/3/337/intel_corporation_tmb.jpg)
Part Number:
Description:
Intel StrataFlash memory 32 Mbit. Access speed 120 ns
Manufacturer:
Intel Corporation
Datasheet:
![E28F320J5-120](/images/manufacturer_photos/0/3/337/intel_corporation_tmb.jpg)
Part Number:
Description:
Intel StrataFlash memory 32 Mbit. Access speed 120 ns
Manufacturer:
Intel Corporation
Datasheet:
![G28F640J5-150](/images/manufacturer_photos/0/3/337/intel_corporation_tmb.jpg)
Part Number:
Description:
Intel StrataFlash memory 64 Mbit. Access speed 150 ns
Manufacturer:
Intel Corporation
Datasheet:
![E28F320J5-100](/images/manufacturer_photos/0/3/337/intel_corporation_tmb.jpg)
Part Number:
Description:
Intel StrataFlash memory 32 Mbit. Access speed 100 ns
Manufacturer:
Intel Corporation
Datasheet:
![DA28F640J5A-150](/images/manufacturer_photos/0/3/337/intel_corporation_tmb.jpg)
Part Number:
Description:
DA28F640J5A-1505 Volt Intel StrataFlash Memory
Manufacturer:
Intel Corporation
Datasheet:
![DA28F320J5A-120](/images/manufacturer_photos/0/3/337/intel_corporation_tmb.jpg)
Part Number:
Description:
5 Volt Intel StrataFlash?? Memory
Manufacturer:
Intel Corporation
Datasheet:
![E28F320J5A-120](/images/manufacturer_photos/0/3/337/intel_corporation_tmb.jpg)
Part Number:
Description:
5 Volt Intel StrataFlash?? Memory
Manufacturer:
Intel Corporation
![NHE6300ESB](/images/manufacturer_photos/0/3/337/intel_corporation_tmb.jpg)
Part Number:
Description:
Intel 6300ESB I/O Controller Hub
Manufacturer:
Intel Corporation
Datasheet:
![NH82801DB](/images/manufacturer_photos/0/3/337/intel_corporation_tmb.jpg)
Part Number:
Description:
Intel 82801DB I/O Controller Hub (ICH4), Pb-Free SLI
Manufacturer:
Intel Corporation
Datasheet: