EP3C5F256C8N Altera, EP3C5F256C8N Datasheet - Page 210

• Manufacturer Part Number: EP3C5F256C8N
• Description: IC CYCLONE III FPGA 5K 256-FBGA
• Manufacturer: Altera
• Series: Cyclone® IIIr

Specifications of EP3C5F256C8N

• Number Of Logic Elements/cells: 5136
• Number Of Labs/clbs: 321
• Total Ram Bits: 423936
• Number Of I /o: 182
• Voltage - Supply: 1.15 V ~ 1.25 V
• Mounting Type: Surface Mount
• Operating Temperature: 0°C ~ 85°C
• Package / Case: 256-FBGA
• No. Of Logic Blocks: 321
• Family Type: Cyclone III
• No. Of I/o's: 182
• I/o Supply Voltage: 3.3V
• Operating Frequency Max: 402MHz
• Operating Temperature Range: 0°C To +85°C
• Rohs Compliant: Yes
• For Use With: 544-2601 - KIT DEV CYCLONE III LS EP3CLS200544-2411 - KIT DEV NIOS II CYCLONE III ED.
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Number Of Gates: -
• Other names: 544-2423; EP3C5F256C8N

9–50
Cyclone III Device Handbook, Volume 1
Figure 9–24. JTAG Configuration of a Single Device Using a Download Cable (2.5, 3.0, and 3.3-V
V
Notes to
(1) Connect these pull-up resistors to the V
(2) Connect the nCONFIG and MSEL[3..0] pins to support a non-JTAG configuration scheme. If you only use a JTAG
(3) Pin 6 of the header is a V
(4) The nCE pin must be connected to GND or driven low for successful JTAG configuration.
(5) The nCEO pin is left unconnected or used as a user I/O pin when it does not feed the nCE pin of another device.
(6) Power up the V
CCIO
configuration, connect the nCONFIG pin to logic high and the MSEL[3..0] pins to ground. In addition, pull DCLK
and DATA[0] either high or low, whichever is convenient on your board.
For this value, refer to the
ByteBlaster II, ByteBlasterMV, and Ethernet Blaster, this pin is a no connect.
from V
MasterBlaster cable. The MasterBlaster cable can receive power from either 5.0- or 3.3-V circuit boards, DC power
supply, or 5.0 V from the USB cable. For this value, refer to the
Guide.
Powering the JTAG Pins)
Figure
Chapter 9: Configuration, Design Security, and Remote System Upgrades in the Cyclone III Device Family
CCA
. Third-party programmers must switch to 2.5 V. Pin 4 of the header is a V
10
V CCIO (1)
9–24:
kΩ
CC
of the ByteBlaster II, USB-Blaster, ByteBlasterMV, or Ethernet Blaster cable with a 2.5- V supply
V CCIO (1)
10
GND
IO
MasterBlaster Serial/USB Communications Cable User
(2)
(2)
(2)
(2)
kΩ
N.C. (5)
reference voltage for the MasterBlaster output driver. V
Cyclone III Device Family
nCE
nCEO
nSTATUS
CONF_DONE
nCONFIG
MSEL[3..0]
DATA[0]
DCLK
CCIO
(4)
supply of the bank in which the pin resides.
TDO
TMS
TCK
TDI
10
kΩ
V CCA
MasterBlaster Serial/USB Communications Cable User
V CCA
10
1
kΩ
kΩ
GND
© December 2009 Altera Corporation
Download Cable 10-Pin Male
Pin 1
Header (Top View)
Guide. In USB-Blaster,
IO
CC
must match the device's V
GND
power supply for the
V
CCA
V
Configuration Features
IO
(6)
(3)
GND
CCA
.