PC28F512P30EFA Micron Technology Inc, PC28F512P30EFA Datasheet - Page 24
![no-image](/images/manufacturer_photos/0/4/441/micron_technology_inc_sml.jpg)
PC28F512P30EFA
Manufacturer Part Number
PC28F512P30EFA
Description
Manufacturer
Micron Technology Inc
Datasheet
1.PC28F512P30EFA.pdf
(86 pages)
Specifications of PC28F512P30EFA
Cell Type
NOR
Density
512Mb
Interface Type
Parallel/Serial
Address Bus
25b
Operating Supply Voltage (typ)
1.8V
Operating Temp Range
-40C to 85C
Package Type
BGA
Program/erase Volt (typ)
8.5 to 9.5V
Sync/async
Async/Sync
Operating Temperature Classification
Industrial
Operating Supply Voltage (min)
1.7V
Operating Supply Voltage (max)
2V
Word Size
16b
Number Of Words
32M
Supply Current
31mA
Mounting
Surface Mount
Pin Count
64
Lead Free Status / Rohs Status
Compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
PC28F512P30EFA
Manufacturer:
MICRON
Quantity:
1 000
Company:
Part Number:
PC28F512P30EFA
Manufacturer:
Micron Technology Inc
Quantity:
10 000
8.0
8.1
8.2
Note:
Datasheet
24
Program Operation
The device supports three programming methods: Word Programming (40h or 10h),
Buffered Programming (E8h, D0h), and Buffered Enhanced Factory Programming (80h,
D0h). The following sections describe device programming in detail.
Successful programming requires the addressed block to be unlocked. If the block is
locked down, WP# must be deasserted and the block must be unlocked before
attempting to program the block. Attempting to program a locked block causes a
program error (SR[4,1] set) and termination of the operation. See
“Security” on page 31
Word Programming
Word programming operations are initiated by writing the Word Program Setup
command to the device. This is followed by a second write to the device with the
address and data to be programmed. The device outputs Status Register data when
read. See
and within the specified V
During programming, the WSM executes a sequence of internally-timed events that
program the desired data bits at the addressed location, and verifies that the bits are
sufficiently programmed. Programming the flash memory array changes “ones” to
“zeros”. Memory array bits that are zeros can be changed to ones only by erasing the
block.
The Status Register can be examined for programming progress and errors by reading
at any address. The device remains in the Read Status Register state until another
command is written to the device.
Status Register bit SR.7 indicates the programming status while the sequence
executes. Commands that can be issued to the device during programming are Read
Status Register, Read Device Identifier, Read CFI, and Read Array (this returns
unknown data).
When programming has finished, Status Register bit SR.4 (when set) indicates a
programming failure. If SR.3 is set, the WSM could not perform the word programming
operation because VPP was outside of its acceptable limits. If SR.1 is set, the word
programming operation attempted to program a locked block, causing the operation to
abort.
Before issuing a new command, the Status Register contents should be examined and
then cleared using the Clear Status Register command. Any valid command can follow,
when word programming has completed.
Buffered Programming
The device features a 512-word buffer to enable optimum programming performance.
For Buffered Programming, data is first written to an on-chip write buffer. Then the
buffer data is programmed into the flash memory array in buffer-size increments. This
can improve system programming performance significantly over non-buffered
programming (see
When the Buffered Programming Setup command is issued, Status Register information
is updated and reflects the availability of the buffer. SR.7 indicates buffer availability: if
set, the buffer is available; if cleared, the buffer is not available.
The device defaults to output SR data after the Buffered Programming Setup Command
(E8h) is issued. CE# or OE# must be toggled to update Status Register. Don’t issue the
Figure 30, “Word Program Flowchart” on page
Figure 32, “Buffer Program Flowchart” on page
for details on locking and unlocking blocks.
PPL
min/max values.
72. VPP must be above V
Order Number: 208042-05
74).
Section 10.0,
P30-65nm
Apr 2010
PPLK
,