GRM1885C1H101J Murata, GRM1885C1H101J Datasheet - Page 147

• Manufacturer Part Number: GRM1885C1H101J
• Manufacturer: Murata

Specifications of GRM1885C1H101J

• Capacitance: 100pF
• Tolerance (+ Or -): 5%
• Voltage: 50VDC
• Temp Coeff (dielectric): C0G
• Operating Temp Range: -55C to 125C
• Mounting Style: Surface Mount
• Package / Case: 0603
• Construction: SMT Chip
• Case Style: Ceramic Chip
• Failure Rate: Not Required
• Wire Form: Not Required
• Product Length (mm): 1.6mm
• Product Depth (mm): 0.8mm
• Product Height (mm): 0.8mm
• Product Diameter (mm): Not Requiredmm
• Dc: 07+
• Lead Free Status / Rohs Status: Compliant

!Note
• This PDF catalog is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our products in it may be discontinued without advance notice. Please check with our
• This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
sales representatives or product engineers before ordering.
!Note
1. Mounting Position
1. Confirm the best mounting position and direction that
2. Information before Mounting
1. Do not re-use capacitors that were removed from the
2. Confirm capacitance characteristics under actual applied
3. Confirm the mechanical stress under actual process and
4. Confirm the rated capacitance, rated voltage and other
3. Maintenance of the Mounting (pick and place) Machine
1. Make sure that the following excessive forces are not
2. Dirt particles and dust accumulated between the suction
!Caution
Soldering and Mounting
minimizes the stress imposed on the capacitor during
flexing or bending the printed circuit board.
1-1. Choose a mounting position that minimizes the
equipment.
voltage.
equipment use.
electrical characteristics before assembly.
applied to the capacitors.
1-1. In mounting the capacitors on the printed circuit
nozzle and the cylinder inner wall prevent the nozzle from
moving smoothly. This imposes greater force upon the
chip during mounting, causing cracked chips. Also the
locating claw, when worn out, imposes uneven forces on
the chip when positioning, causing cracked chips. The
suction nozzle and the locating claw must be maintained,
checked and replaced periodically.
• Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
stress imposed on the chip during flexing or bending
of the board.
board, any bending force against them shall be kept
to a minimum to prevent them from any bending
damage or cracking. Please take into account the
following precautions and recommendations for use
in your process.
(1) Adjust the lowest position of the pickup nozzle so
(2) Adjust the nozzle pressure within a static load of
as not to bend the printed circuit board.
1N to 3N during mounting.
5. Prior to use, confirm the Solderability for the capacitors
6. Prior to measuring capacitance, carry out a heat
7. The use of Sn-Zn based solder will deteriorate the
[Component Direction]
[Chip Mounting Close to Board Separation Point]
[Incorrect]
[Correct]
that were in long-term storage.
treatment for capacitors that were in long-term storage.
reliability of the MLCC.
Please contact our sales representative or product
engineers on the use of Sn-Zn based solder in advance.
Perforation
Suction Nozzle
Board
A
Slit
B
Support Pin
D
C
Deflection
Continued on the following page.
Chip arrangement
Worst A-C-(B~D) Best
!Caution
Locate chip
horizontal to the
direction in
which stress
acts.
Board Guide
145
C02E.pdf
09.9.18
8