ATmega32C1 Automotive Atmel Corporation, ATmega32C1 Automotive Datasheet - Page 214

• Manufacturer Part Number: ATmega32C1 Automotive
• Manufacturer: Atmel Corporation

Specifications of ATmega32C1 Automotive

• Flash (kbytes): 32 Kbytes
• Pin Count: 32
• Max. Operating Frequency: 16 MHz
• Cpu: 8-bit AVR
• # Of Touch Channels: 12
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 27
• Ext Interrupts: 27
• Usb Speed: No
• Usb Interface: No
• Spi: 1
• Uart: 1
• Can: 1
• Lin: 1
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 11
• Adc Resolution (bits): 10
• Adc Speed (ksps): 125
• Analog Comparators: 4
• Resistive Touch Screen: No
• Dac Channels: 1
• Dac Resolution (bits): 10
• Temp. Sensor: Yes
• Crypto Engine: No
• Sram (kbytes): 2
• Eeprom (bytes): 1024
• Self Program Memory: YES
• Dram Memory: No
• Nand Interface: No
• Picopower: No
• Temp. Range (deg C): -40 to 150
• I/o Supply Class: 2.7 to 5.5
• Operating Voltage (vcc): 2.7 to 5.5
• Fpu: No
• Mpu / Mmu: no / no
• Timers: 2
• Output Compare Channels: 4
• Input Capture Channels: 1
• Pwm Channels: 4
• 32khz Rtc: No
• Calibrated Rc Oscillator: Yes

17.5.5.2
17.5.6
17.5.6.1
214
Atmel ATmega16/32/64/M1/C1
Bit Timing
Busy Signal in UART Mode
Baud rate Generator
When the busy signal is set, some registers are locked, user writing is not allowed:
If the busy signal is set, the only available commands are:
Note that, if another command is entered during busy signal, the new command is not vali-
dated and the LOVRERR bit flag of the LINERR register is set. The on-going transfer is not
interrupted.
During the byte transmission, the busy signal is set. This locks some registers from being
written:
The busy signal is not generated during a byte reception.
The baud rate is defined to be the transfer rate in bits per second (bps):
Equation for calculating baud rate:
Equation for setting LINDIV value:
Note that in reception a majority vote on three samplings is made.
• “LIN Control Register” - LINCR - except LCMD[2..0], LENA & LSWRES,
• “LIN Baud Rate Registers” - LINBRRL & LINBRRH,
• “LIN Data Length Register” - LINDLR,
• “LIN Identifier Register” - LINIDR,
• “LIN Data Register” - LINDAT.
• LCMD[1..0] = 00
• LENA = 0 and/or LCMD[2] = 0, the kill command is taken into account immediately,
• LSWRES = 1, the reset command is taken into account immediately.
• “LIN Control Register” - LINCR - except LCMD[2..0], LENA & LSWRES,
• “LIN Data Register” - LINDAT.
• BAUD: Baud rate (in bps),
•
• LDIV[11..0]: Contents of LINBRRH & LINBRRL registers - (0-4095), the pre-scaler
• LBT[5..0]: Least significant bits of - LINBTR register- (0-63) is the number of samplings in a
f
receives clk
LIN or UART bit (default value 32).
clk
i/o
: System I/O clock frequency,
i/o
as input clock.
b
, the abort command is taken into account at the end of the byte,
BAUD =
LDIV[11..0] = (
f
clk
i/o
/ LBT[5..0] x (LDIV[11..0] + 1)
f
clk
i/o
/ LBT[5..0] x BAUD ) - 1
7647G–AVR–09/11