ATmega32C1 Automotive Atmel Corporation, ATmega32C1 Automotive Datasheet - Page 350

no-image

ATmega32C1 Automotive

Manufacturer Part Number
ATmega32C1 Automotive
Description
Manufacturer
Atmel Corporation

Specifications of ATmega32C1 Automotive

Flash (kbytes)
32 Kbytes
Pin Count
32
Max. Operating Frequency
16 MHz
Cpu
8-bit AVR
# Of Touch Channels
12
Hardware Qtouch Acquisition
No
Max I/o Pins
27
Ext Interrupts
27
Usb Speed
No
Usb Interface
No
Spi
1
Uart
1
Can
1
Lin
1
Graphic Lcd
No
Video Decoder
No
Camera Interface
No
Adc Channels
11
Adc Resolution (bits)
10
Adc Speed (ksps)
125
Analog Comparators
4
Resistive Touch Screen
No
Dac Channels
1
Dac Resolution (bits)
10
Temp. Sensor
Yes
Crypto Engine
No
Sram (kbytes)
2
Eeprom (bytes)
1024
Self Program Memory
YES
Dram Memory
No
Nand Interface
No
Picopower
No
Temp. Range (deg C)
-40 to 150
I/o Supply Class
2.7 to 5.5
Operating Voltage (vcc)
2.7 to 5.5
Fpu
No
Mpu / Mmu
no / no
Timers
2
Output Compare Channels
4
Input Capture Channels
1
Pwm Channels
4
32khz Rtc
No
Calibrated Rc Oscillator
Yes
Notes:
350
0x1B (0x3B)
0x1A (0x3A)
0x0E (0x2E)
0x0D (0x2D)
0x0C (0x2C)
0x0B (0x2B)
0x0A (0x2A)
0x19 (0x39)
0x18 (0x38)
0x17 (0x37)
0x16 (0x36)
0x15 (0x35)
0x14 (0x34)
0x13 (0x33)
0x12 (0x32)
0x11 (0x31)
0x10 (0x30)
0x0F (0x2F)
0x09 (0x29)
0x08 (0x28)
0x07 (0x27)
0x06 (0x26)
0x05 (0x25)
0x04 (0x24)
0x03 (0x23)
0x02 (0x22)
0x01 (0x21)
0x00 (0x20)
Address
1. For compatibility with future devices, reserved bits should be written to zero if accessed. Reserved I/O memory addresses
2. I/O Registers within the address range 0x00 - 0x1F are directly bit-accessible using the SBI and CBI instructions. In these
3. Some of the status flags are cleared by writing a logical one to them. Note that, unlike most other AVRs, the CBI and SBI
4. When using the I/O specific commands IN and OUT, the I/O addresses 0x00 - 0x3F must be used. When addressing I/O
5. These registers are only available on ATmega32/64M1. For other products described in this datasheet, these locations are
Atmel ATmega16/32/64/M1/C1
should never be written.
registers, the value of single bits can be checked by using the SBIS and SBIC instructions.
instructions will only operate on the specified bit, and can therefore be used on registers containing such status flags. The
CBI and SBI instructions work with registers 0x00 to 0x1F only.
Registers as data space using LD and ST instructions, 0x20 must be added to these addresses. The
ATmega16/32/64/M1/C1 is a complex microcontroller with more peripheral units than can be supported within the 64 loca-
tion reserved in Opcode for the IN and OUT instructions. For the Extended I/O space from 0x60 - 0xFF in SRAM, only the
ST/STS/STD and LD/LDS/LDD instructions can be used.
reserved.
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
GPIOR2
GPIOR1
PORTE
PORTD
PORTC
PORTB
Name
PCIFR
DDRE
DDRD
DDRC
DDRB
TIFR1
TIFR0
PINE
PIND
PINC
PINB
GPIOR27
GPIOR17
PORTD7
PORTC7
PORTB7
PIND7
PINC7
PINB7
DDD7
DDC7
Bit 7
DDB7
GPIOR26
GPIOR16
PORTD6
PORTC6
PORTB6
PIND6
PINC6
PINB6
DDD6
DDC6
DDB6
Bit 6
GPIOR25
GPIOR15
PORTD5
PORTC5
PORTB5
PIND5
PINC5
PINB5
DDD5
DDC5
Bit 5
DDB5
ICF1
GPIOR24
GPIOR14
PORTD4
PORTC4
PORTB4
PIND4
PINC4
PINB4
DDD4
DDC4
DDB4
Bit 4
GPIOR23
GPIOR13
PORTD3
PORTC3
PORTB3
PCIF3
PIND3
PINC3
PINB3
DDD3
DDC3
DDB3
Bit 3
GPIOR22
GPIOR12
PORTE2
PORTD2
PORTC2
PORTB2
OCF1B
OCF0B
PIND2
PINC2
PCIF2
PINE2
DDD2
DDC2
PINB2
Bit 2
DDE2
DDB2
GPIOR21
GPIOR11
PORTD1
PORTC1
PORTE1
PORTB1
OCF1A
OCF0A
PCIF1
PINE1
PIND1
PINC1
PINB1
DDE1
DDD1
DDC1
DDB1
Bit 1
GPIOR20
GPIOR10
PORTE0
PORTD0
PORTC0
PORTB0
PCIF0
PINE0
PIND0
PINC0
PINB0
TOV1
TOV0
DDE0
DDD0
DDC0
DDB0
Bit 0
7647G–AVR–09/11
page 135
page 106
page 85
page 28
page 28
page 81
page 81
page 81
page 80
page 80
page 81
page 80
page 80
page 80
page 80
page 80
page 80
Page

Related parts for ATmega32C1 Automotive