SAM7S32 Atmel Corporation, SAM7S32 Datasheet - Page 130

• Manufacturer Part Number: SAM7S32
• Manufacturer: Atmel Corporation

Specifications of SAM7S32

• Flash (kbytes): 32 Kbytes
• Pin Count: 48
• Max. Operating Frequency: 55 MHz
• Cpu: ARM7TDMI
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 21
• Ext Interrupts: 21
• Usb Speed: No
• Usb Interface: No
• Spi: 1
• Twi (i2c): 1
• Uart: 2
• Ssc: 1
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 8
• Adc Resolution (bits): 10
• Adc Speed (ksps): 384
• Resistive Touch Screen: No
• Temp. Sensor: No
• Crypto Engine: No
• Sram (kbytes): 8
• Self Program Memory: NO
• Dram Memory: No
• Nand Interface: No
• Picopower: No
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 1.8/3.3
• Operating Voltage (vcc): 3.0 to 3.6
• Fpu: No
• Mpu / Mmu: no / no
• Timers: 3
• Output Compare Channels: 3
• Input Capture Channels: 3
• Pwm Channels: 4
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: No

20.2.5
20.2.5.1
130
SAM7S Series
Device Operations
Flash Read Command
Several commands on the Flash memory are available. These commands are summarized in
Table 20-3 on page
face running several read/write handshaking sequences.
When a new command is executed, the previous one is automatically achieved. Thus, chaining
a read command after a write automatically flushes the load buffer in the Flash.
In the following tables, 21-6 through 21-18
This command is used to read the contents of the Flash memory. The read command can start
at any valid address in the memory plane and is optimized for consecutive reads. Read hand-
shaking can be chained; an internal address buffer is automatically increased.
Table 20-6.
Table 20-7.
Step
1
2
3
4
5
...
n
n+1
n+2
n+3
...
Step
1
2
3
4
5
6
7
...
n
• DATA[15:0] pertains to SAM7S512/256/128/64/321/161
• DATA[7:0] pertains to SAM7S32/16
Handshake Sequence
Write handshaking
Write handshaking
Write handshaking
Read handshaking
Read handshaking
...
Write handshaking
Write handshaking
Read handshaking
Read handshaking
...
Handshake Sequence
Write handshaking
Write handshaking
Write handshaking
Write handshaking
Write handshaking
Read handshaking
Read handshaking
...
Write handshaking
Read Command
Read Command
126. Each command is driven by the programmer through the parallel inter-
MODE[3:0]
CMDE
ADDR0
ADDR1
DATA
DATA
...
ADDR0
ADDR1
DATA
DATA
...
MODE[3:0]
CMDE
ADDR0
ADDR1
ADDR2
ADDR3
DATA
DATA
...
ADDR0
DATA[15:0]
READ
Memory Address LSB
Memory Address
*Memory Address++
*Memory Address++
...
Memory Address LSB
Memory Address
*Memory Address++
*Memory Address++
...
READ
Memory Address LSB
Memory Address
Memory Address
Memory Address
*Memory Address++
*Memory Address++
...
Memory Address LSB
DATA[7:0]
6175L–ATARM–28-Jul-11