SAM7S32 Atmel Corporation, SAM7S32 Datasheet - Page 611

• Manufacturer Part Number: SAM7S32
• Manufacturer: Atmel Corporation

Specifications of SAM7S32

• Flash (kbytes): 32 Kbytes
• Pin Count: 48
• Max. Operating Frequency: 55 MHz
• Cpu: ARM7TDMI
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 21
• Ext Interrupts: 21
• Usb Speed: No
• Usb Interface: No
• Spi: 1
• Twi (i2c): 1
• Uart: 2
• Ssc: 1
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 8
• Adc Resolution (bits): 10
• Adc Speed (ksps): 384
• Resistive Touch Screen: No
• Temp. Sensor: No
• Crypto Engine: No
• Sram (kbytes): 8
• Self Program Memory: NO
• Dram Memory: No
• Nand Interface: No
• Picopower: No
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 1.8/3.3
• Operating Voltage (vcc): 3.0 to 3.6
• Fpu: No
• Mpu / Mmu: no / no
• Timers: 3
• Output Compare Channels: 3
• Input Capture Channels: 3
• Pwm Channels: 4
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: No

40.5.8.3
40.5.8.4
40.5.8.5
40.5.9
40.5.9.1
40.5.9.2
40.5.9.3
6175L–ATARM–28-Jul-11
Universal Synchronous Asynchronous Receiver Transmitter (USART)
TWI: Disabling Does not Operate Correctly
USART: Hardware Handshaking – Two Characters Sent
TWI: NACK Status Bit Lost
TWI: Possible Receive Holding Register Corruption
USART: CTS in Hardware Handshaking
USART: XOFF Character Bad Behavior
Any transfer in progress is immediately frozen if the Control Register (TWI_CR) is written with
the bit MSDIS at 1. Furthermore, the status bits TXCOMP and TXRDY in the Status Register
(TWI_SR) are not reset.
The user must wait for the end of transfer before disabling the TWI. In addition, the interrupts
must be disabled before disabling the TWI.
During a master frame, if TWI_SR is read between the Non Acknowledge condition detection
and the TXCOMP bit rising in the TWI_SR, the NACK bit is not set.
The user must wait for the TXCOMP status bit by interrupt and must not read the TWI_SR as
long as transmission is not completed.
TXCOMP and NACK fields are set simultaneously and the NACK field is reset after the read of
the TWI_SR.
When loading the TWI_RHR, the transfer direction is ignored. The last data byte received in the
TWI_RHR is corrupted at the end of the first subsequent transmit data byte. Neither RXRDY nor
OVERRUN status bits are set if this occurs.
The user must be sure that received data is read before transmitting any new data.
When Hardware Handshaking is used and if CTS goes high near the end of the start bit, a char-
acter can be lost.
CTS must not go high during a time slot occurring between 2 Master Clock periods before and
16 Master Clock periods after the rising edge of the start bit.
None.
If CTS switches from 0 to 1 during the TX of a character and if the holding register (US_THR) is
not empty, the content of US_THR will also be transmitted.
Don't use the PDC in transmit mode and do not fill US_THR before TXEMPTY is set at 1.
The XOFF character is sent only when the receive buffer is detected full. While the XOFF is
being sent, the remote transmitter is still transmitting. As only one Holding register is available in
the receiver, characters will be lost in reception. This makes the software handshaking function-
ality ineffective.
Problem Fix/Workaround
Problem Fix/Workaround
Problem Fix/Workaround
Problem Fix/Workaround
Problem Fix/Workaround
SAM7S Series
611