SAM7S32 Atmel Corporation, SAM7S32 Datasheet - Page 361

• Manufacturer Part Number: SAM7S32
• Manufacturer: Atmel Corporation

Specifications of SAM7S32

• Flash (kbytes): 32 Kbytes
• Pin Count: 48
• Max. Operating Frequency: 55 MHz
• Cpu: ARM7TDMI
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 21
• Ext Interrupts: 21
• Usb Speed: No
• Usb Interface: No
• Spi: 1
• Twi (i2c): 1
• Uart: 2
• Ssc: 1
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 8
• Adc Resolution (bits): 10
• Adc Speed (ksps): 384
• Resistive Touch Screen: No
• Temp. Sensor: No
• Crypto Engine: No
• Sram (kbytes): 8
• Self Program Memory: NO
• Dram Memory: No
• Nand Interface: No
• Picopower: No
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 1.8/3.3
• Operating Voltage (vcc): 3.0 to 3.6
• Fpu: No
• Mpu / Mmu: no / no
• Timers: 3
• Output Compare Channels: 3
• Input Capture Channels: 3
• Pwm Channels: 4
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: No

31.6.1.1
31.6.1.2
Table 31-2.
6175L–ATARM–28-Jul-11
Source Clock
3 686 400
4 915 200
5 000 000
7 372 800
MHz
Baud Rate in Asynchronous Mode
Baud Rate Calculation Example
Baud Rate Example (OVER = 0)
Expected Baud
If the external SCK clock is selected, the duration of the low and high levels of the signal pro-
vided on the SCK pin must be longer than a Master Clock (MCK) period. The frequency of the
signal provided on SCK must be at least 4.5 times lower than MCK.
Figure 31-5. Baud Rate Generator
If the USART is programmed to operate in asynchronous mode, the selected clock is first
divided by CD, which is field programmed in the Baud Rate Generator Register (US_BRGR).
The resulting clock is provided to the receiver as a sampling clock and then divided by 16 or 8,
depending on the programming of the OVER bit in US_MR.
If OVER is set to 1, the receiver sampling is 8 times higher than the baud rate clock. If OVER is
cleared, the sampling is performed at 16 times the baud rate clock.
The following formula performs the calculation of the Baud Rate.
This gives a maximum baud rate of MCK divided by 8, assuming that MCK is the highest possi-
ble clock and that OVER is programmed at 1.
Table 31-2
clock frequencies. This table also shows the actual resulting baud rate and the error.
SCK
38 400
38 400
38 400
38 400
Rate
Bit/s
Reserved
MCK/DIV
Baudrate
MCK
shows calculations of CD to obtain a baud rate at 38400 bauds for different source
USCLKS
=
0
1
2
3
Calculation Result
--------------------------------------------- -
(
SelectedClock
8 2 Over
(
–
12.00
6.00
8.00
8.14
16-bit Counter
)CD
CD
)
USCLKS = 3
CD
12
6
8
8
0
SYNC
CD
>1
1
0
Actual Baud Rate
1
0
38 400.00
38 400.00
39 062.50
38 400.00
Bit/s
OVER
Sampling
Divider
SAM7S Series
FIDI
0
1
SYNC
0.00%
0.00%
1.70%
0.00%
Error
SCK
Baud Rate
Sampling
Clock
Clock
361