SAM7S32 Atmel Corporation, SAM7S32 Datasheet - Page 132

• Manufacturer Part Number: SAM7S32
• Manufacturer: Atmel Corporation

Specifications of SAM7S32

• Flash (kbytes): 32 Kbytes
• Pin Count: 48
• Max. Operating Frequency: 55 MHz
• Cpu: ARM7TDMI
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 21
• Ext Interrupts: 21
• Usb Speed: No
• Usb Interface: No
• Spi: 1
• Twi (i2c): 1
• Uart: 2
• Ssc: 1
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 8
• Adc Resolution (bits): 10
• Adc Speed (ksps): 384
• Resistive Touch Screen: No
• Temp. Sensor: No
• Crypto Engine: No
• Sram (kbytes): 8
• Self Program Memory: NO
• Dram Memory: No
• Nand Interface: No
• Picopower: No
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 1.8/3.3
• Operating Voltage (vcc): 3.0 to 3.6
• Fpu: No
• Mpu / Mmu: no / no
• Timers: 3
• Output Compare Channels: 3
• Input Capture Channels: 3
• Pwm Channels: 4
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: No

20.2.5.3
20.2.5.4
132
SAM7S Series
Flash Full Erase Command
Flash Lock Commands
Table 20-9.
The Flash command Write Page and Lock (WPL) is equivalent to the Flash Write Command.
However, the lock bit is automatically set at the end of the Flash write operation. As a lock region
is composed of several pages, the programmer writes to the first pages of the lock region using
Flash write commands and writes to the last page of the lock region using a Flash write and lock
command.
The Flash command Erase Page and Write (EWP) is equivalent to the Flash Write Command.
However, before programming the load buffer, the page is erased.
The Flash command Erase Page and Write the Lock (EWPL) combines EWP and WPL
commands.
This command is used to erase the Flash memory planes.
All lock regions must be unlocked before the Full Erase command by using the CLB command.
Otherwise, the erase command is aborted and no page is erased.
Table 20-10. Full Erase Command
Lock bits can be set using WPL or EWPL commands. They can also be set by using the Set
Lock command (SLB). With this command, several lock bits can be activated. A Bit Mask is pro-
vided as argument to the command. When bit 0 of the bit mask is set, then the first lock bit is
activated.
Step
5
6
7
...
n
n+1
n+2
n+3
n+4
n+5
...
Step
1
2
Handshake Sequence
Write handshaking
Write handshaking
Write handshaking
...
Write handshaking
Write handshaking
Write handshaking
Write handshaking
Write handshaking
Write handshaking
...
Handshake Sequence
Write handshaking
Write handshaking
Write Command (Continued)
MODE[3:0]
ADDR3
DATA
DATA
...
ADDR0
ADDR1
ADDR2
ADDR3
DATA
DATA
...
MODE[3:0]
CMDE
DATA
DATA[7:0]
Memory Address
*Memory Address++
*Memory Address++
...
Memory Address LSB
Memory Address
Memory Address
Memory Address
*Memory Address++
*Memory Address++
...
DATA[15:0] or DATA[7:0]
EA
0
6175L–ATARM–28-Jul-11