SAM9XE512 Atmel Corporation, SAM9XE512 Datasheet - Page 839

• Manufacturer Part Number: SAM9XE512
• Manufacturer: Atmel Corporation

Specifications of SAM9XE512

• Flash (kbytes): 512 Kbytes
• Pin Count: 217
• Max. Operating Frequency: 180 MHz
• Cpu: ARM926
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 96
• Ext Interrupts: 96
• Usb Transceiver: 3
• Usb Speed: Full Speed
• Usb Interface: Host, Device
• Spi: 2
• Twi (i2c): 2
• Uart: 6
• Ssc: 1
• Ethernet: 1
• Sd / Emmc: 1
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: Yes
• Adc Channels: 4
• Adc Resolution (bits): 10
• Adc Speed (ksps): 312
• Resistive Touch Screen: No
• Temp. Sensor: No
• Crypto Engine: No
• Sram (kbytes): 32
• Self Program Memory: NO
• External Bus Interface: 1
• Dram Memory: sdram
• Nand Interface: Yes
• Picopower: No
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 1.8/3.3
• Operating Voltage (vcc): 1.65 to 1.95
• Fpu: No
• Mpu / Mmu: No / Yes
• Timers: 6
• Output Compare Channels: 6
• Input Capture Channels: 6
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: No

46.2.3.5
46.2.3.6
46.2.4
46.2.4.1
46.2.5
46.2.5.1
6254C–ATARM–22-Jan-10
Reset Controller (RSTC)
Static Memory Controller (SMC)
MCI: Small Block Reading
MCI: old SDCard Compatibility
RSTC: Reset Type Status is wrong at power-up
SMC: Chip Select Parameters Modification
Enable the interrupts related to ENDRX, ENDTX, RXBUFF and TXBUFE only after enabling the
PDC channel by writing PDC_TXTEN or PDC_RXTEN.
In case of a read of a small block (i.e., 5 bytes) by the READ_SINGLE_BLOCK command
(CMD17), the DATA FSM may not perform correctly. This occurs if the read transfer is done
before the response start bit is sent by the card. It leads to erratic behavior of the NOTBUSY flag
and to a false data time-out error, DTOE.
None.
Busy line is sampled 2 clock cycles after the command End Bit when the R1B response type is
expected. This timing is not strictly defined in SD mode.
This timing is defined with MMC specification 4.1. (R1b Busy Timing)
None.
RSTTYP status in the Reset Controller Status Register is wrong at power-up.
It should be “0” (General Reset) but it is “5” (Brownout Reset). The value is the same if Brownout
and Brownout Reset are enabled or not. The BODSTS bit remains correct.
None.
The user must not change the configuration parameters of an SMC Chip Select (Setup, Pulse,
Cycle, Mode) if accesses are performed on this CS during the modification.
For example, the modification of the Chip Select 0 (CS0) parameters, while fetching the code
from a memory connected on this CS0, may lead to unpredictable behavior.
The code used to modify the parameters of an SMC Chip Select can be executed from the inter-
nal RAM or from a memory connected to another Chip Select.
Problem Fix/Workaround
Problem Fix/Workaround
Problem Fix/Workaround
Problem Fix/Workaround
AT91SAM9XE128/256/512 Preliminary
839