AD7192 Analog Devices, AD7192 Datasheet - Page 10
![no-image](/images/manufacturer_photos/0/0/56/analog_devices_sml.jpg)
AD7192
Manufacturer Part Number
AD7192
Description
4.8 kHz Ultra-Low Noise 24-Bit Sigma-Delta ADC with PGA
Manufacturer
Analog Devices
Datasheet
1.AD7192.pdf
(40 pages)
Specifications of AD7192
Resolution (bits)
24bit
# Chan
4
Sample Rate
4.8kSPS
Interface
Ser,SPI
Analog Input Type
Diff-Bip,Diff-Uni,SE-Bip,SE-Uni
Ain Range
± (Vref/Gain)
Adc Architecture
Sigma-Delta
Pkg Type
SOP
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
AD7192BRUZ
Manufacturer:
ADI
Quantity:
1 000
Company:
Part Number:
AD7192BRUZ
Manufacturer:
AD
Quantity:
1 831
Company:
Part Number:
AD7192BRUZ
Manufacturer:
ADI
Quantity:
325
Part Number:
AD7192BRUZ
Manufacturer:
ADI/亚德诺
Quantity:
20 000
Company:
Part Number:
AD7192BRUZ-REEL
Manufacturer:
ADI
Quantity:
1 000
AD7192
PIN CONFIGURATION AND FUNCTION DESCRIPTIONS
Table 5. Pin Function Descriptions
Pin No.
1
2
3
4
5
6
7
8
9
10
11
12
Mnemonic
MCLK1
MCLK2
SCLK
CS
P3
P2
P1/REFIN2(+)
P0/REFIN2(−)
NC
AINCOM
AIN1
AIN2
Description
When the master clock for the device is provided externally by a crystal, the crystal is connected between
MCLK1 and MCLK2.
Master Clock Signal for the Device. The AD7192 has an internal 4.92 MHz clock. This internal clock can be
made available on the MCLK2 pin. The clock for the AD7192 can be provided externally also in the form of a
crystal or external clock. A crystal can be tied across the MCLK1 and MCLK2 pins. Alternatively, the MCLK2 pin
can be driven with a CMOS-compatible clock and the MCLK1 pin left unconnected.
Serial Clock Input. This serial clock input is for data transfers to and from the ADC. The SCLK has a Schmitt-
triggered input, making the interface suitable for opto-isolated applications. The serial clock can be
continuous with all data transmitted in a continuous train of pulses. Alternatively, it can be a noncontinuous
clock with the information transmitted to or from the ADC in smaller batches of data.
Chip Select Input. This is an active low logic input used to select the ADC. CS can be used to select the ADC in
systems with more than one device on the serial bus or as a frame synchronization signal in communicating
with the device. CS can be hardwired low, allowing the ADC to operate in 3-wire mode with SCLK, DIN, and
DOUT used to interface with the device.
Digital Output Pin. This pin can function as a general-purpose output bit referenced between AV
Digital Output Pin. This pin can function as a general-purpose output bit referenced between AV
Digital Output Pin/Positive Reference Input. This pin functions as a general-purpose output bit referenced
between AV
An external reference can be applied between REFIN2(+) and REFIN2(−). REFIN2(+) can lie anywhere between
AV
with a reference from 1 V to AV
Digital Output Pin/Negative Reference Input. This pin functions as a general-purpose output bit referenced
between AV
This reference input can lie anywhere between AGND and AV
No Connect. This pin should be tied to AGND.
Analog inputs AIN1 to AIN4 are referenced to this input when configured for pseudodifferential operation.
Analog Input. This pin can be configured as the positive input of a fully differential input pair when used with
AIN2 or as a pseudodifferential input when used with AINCOM.
Analog Input. This pin can be configured as the negative input of a fully differential input pair when used
with AIN1 or as a pseudodifferential input when used with AINCOM.
DD
and AGND + 1 V. The nominal reference voltage, (REFIN2(+) − REFIN2(−)), is AV
DD
DD
and AGND. When the REFSEL bit in the configuration register = 1, this pin functions as REFIN2(+).
and AGND. When the REFSEL bit in the configuration register = 1, this pin functions as REFIN2(−).
P1/REFIN2(+)
P0/REFIN2(–)
AINCOM
MCLK1
MCLK2
SCLK
AIN1
AIN2
NC
CS
P3
P2
Figure 5. Pin Configuration
10
12
11
1
2
3
4
5
6
7
8
9
DD
Rev. A | Page 10 of 40
NC = NO CONNECT
.
(Not to Scale)
AD7192
TOP VIEW
24
22
20
19
18
17
16
15
14
13
23
21
DIN
DOUT/RDY
SYNC
DV
AV
DGND
AGND
BPDSW
REFIN1(–)
REFIN1(+)
AIN4
AIN3
DD
DD
DD
− 1 V.
DD
, but the part functions
DD
DD
and AGND.
and AGND.