AD9866 Analog Devices, AD9866 Datasheet - Page 44
![no-image](/images/manufacturer_photos/0/0/56/analog_devices_sml.jpg)
AD9866
Manufacturer Part Number
AD9866
Description
Manufacturer
Analog Devices
Datasheet
1.AD9866.pdf
(48 pages)
Specifications of AD9866
Resolution (bits)
12bit
# Chan
1
Sample Rate
80MSPS
Interface
Nibble
Analog Input Type
Diff-Uni
Ain Range
6.3 V p-p,8 mV p-p
Adc Architecture
Pipelined
Pkg Type
CSP
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
AD9866BCP
Manufacturer:
ADI
Quantity:
329
Part Number:
AD9866BCP
Manufacturer:
ADI/亚德诺
Quantity:
20 000
Part Number:
AD9866BCPZ
Manufacturer:
ADI/亚德诺
Quantity:
20 000
Company:
Part Number:
AD9866BCPZRL
Manufacturer:
SAMSUNG
Quantity:
2 100
AD9866
PCB DESIGN CONSIDERATIONS
Although the AD9866 is a mixed-signal device, the part should
be treated as an analog component. The on-chip digital cir-
cuitry has been specially designed to minimize the impact of its
digital switching noise on the MxFE’s analog performance.
To achieve the best performance, the power, grounding, and
layout recommendations in this section should be followed.
Assembly instructions for the micro-lead frame package can be
found in an application note from Amkor at: www.amkor.com/
products/notes_papers/MLF_AppNote_0902.pdf.
COMPONENT PLACEMENT
If the three following guidelines of component placement are
followed, chances for getting the best performance from the
MxFE are greatly increased. First, manage the path of return
currents flowing in the ground plane so that high frequency
switching currents from the digital circuits do not flow on the
ground plane under the MxFE or analog circuits. Second, keep
noisy digital signal paths and sensitive receive signal paths as
short as possible. Third, keep digital (noise generating) and
analog (noise susceptible) circuits as far away from each other
as possible.
To best manage the return currents, pure digital circuits that
generate high switching currents should be closest to the power
supply entry. This keeps the highest frequency return current
paths short and prevents them from traveling over the sensitive
MxFE and analog portions of the ground plane. Also, these
circuits should be generously bypassed at each device, which
further reduces the high frequency ground currents. The MxFE
should be placed adjacent to the digital circuits, such that the
ground return currents from the digital sections do not flow in
the ground plane under the MxFE.
The AD9866 has several pins that are used to decouple sensitive
internal nodes. These pins are REFIO, REFB, and REFT. The
decoupling capacitors connected to these points should have
low ESR and ESL. These capacitors should be placed as close to
the MxFE as possible (see Figure 75) and be connected directly
to the analog ground plane. The resistor connected to the
REFADJ pin should also be placed close to the device and
connected directly to the analog ground plane.
Rev. B | Page 44 of 48
POWER PLANES AND DECOUPLING
While the AD9866 evaluation board demonstrates a very good
power supply distribution and decoupling strategy, it can be
further simplified for many applications. The board has four
layers: two signal layers, one ground plane, and one power
plane. While the power plane on the evaluation board is split
into multiple analog and digital subsections, a permissible
alternative would be to have AVDD and CLKVDD share the
same analog 3.3 V power plane. A separate analog plane/supply
may be allocated to the IAMP, if its supply voltage differs from
the 3.3 V required by AVDD and CLKVDD. On the digital
side, DVDD and DRVDD can share the same 3.3 V digital
power plane. This digital power plane brings the current used
to power the digital portion of the MxFE and its output drivers.
This digital plane should be kept from going underneath the
analog components.
The analog and digital power planes allocated to the MxFE may
be fed from the same low noise voltage source; however, they
should be decoupled from each other to prevent the noise
generated in the digital portion of the MxFE from corrupting
the AVDD supply. This can be done by using ferrite beads be-
tween the voltage source and the respective analog and digital
power planes with a low ESR, bulk decoupling capacitor on the
MxFE side of the ferrite. Each of the MxFE’s supply pins (AVDD,
CLKVDD, DVDD, and DRVDD) should also have dedicated
low ESR, ESL decoupling capacitors. The decoupling capacitors
should be placed as close to the MxFE supply pins as possible.
GROUND PLANES
The AD9866 evaluation board uses a single serrated ground plane
to help prevent any high frequency digital ground currents from
coupling over to the analog portion of the ground plane. The
digital currents affiliated with the high speed data bus interface
(Pin 1 to Pin 16) have the highest potential of generating
problematic high frequency noise. A ground serration that contains
these currents should reduce the effects of this potential noise source.
The ground plane directly underneath the MxFE should be
continuous and uniform. The 64-lead LFCSP package is designed
to provide excellent thermal conductivity. This is partly achieved by
incorporating an exposed die paddle on the bottom surface of the
package. However, to take full advantage of this feature, the PCB
must have features to effectively conduct heat away from the
package. This can be achieved by incorporating thermal pad and
thermal vias on the PCB. While a thermal pad provides a
solderable surface on the top surface of the PCB (to solder the
package die paddle on the board), thermal vias are needed to
provide a thermal path to inner and/or bottom layers of the
PCB to remove the heat.
Lastly, all ground connections should be made as short as possible.
This results in the lowest impedance return paths and the
quietest ground connections.