STM8S103F3 STMicroelectronics, STM8S103F3 Datasheet - Page 25

no-image

STM8S103F3

Manufacturer Part Number
STM8S103F3
Description
Access line, 16 MHz STM8S 8-bit MCU, up to 8 Kbytes Flash, data EEPROM
Manufacturer
STMicroelectronics
Datasheet

Specifications of STM8S103F3

Program Memory
8 Kbytes Flash; data retention 20 years at 55 °C after 10 kcycles
Data Memory
640 bytes true data EEPROM; endurance 300 kcycles
Ram
1 Kbytes
Advanced Control Timer
16-bit, 4 CAPCOM channels, 3 complementary outputs, dead-time insertion and flexible synchronization

Available stocks

Company
Part Number
Manufacturer
Quantity
Price
Company:
Bonase Electronics (HK) Co., Limited Bonase Electronics (HK) Co., Limited
Part Number:
STM8S103F3M6
Manufacturer:
FSC
Quantity:
4 500
Price:
Company:
Bonase Electronics (HK) Co., Limited Bonase Electronics (HK) Co., Limited
Part Number:
STM8S103F3M6TR
Manufacturer:
SONY
Quantity:
12 500
Price:
Company:
Bonase Electronics (HK) Co., Limited Bonase Electronics (HK) Co., Limited
Part Number:
STM8S103F3P3
Manufacturer:
ON
Quantity:
3 206
Price:
Company:
Bonase Electronics (HK) Co., Limited Bonase Electronics (HK) Co., Limited
Part Number:
STM8S103F3P3TR
Manufacturer:
STMicroelectronics
Quantity:
2 000
Price:
Company:
Bonase Electronics (HK) Co., Limited Bonase Electronics (HK) Co., Limited
Part Number:
STM8S103F3P6
Manufacturer:
ST
Quantity:
3 000
Price:
Company:
Bonase Electronics (HK) Co., Limited Bonase Electronics (HK) Co., Limited
Part Number:
STM8S103F3P6.
Manufacturer:
ST
Quantity:
15 000
Price:
Company:
Bonase Electronics (HK) Co., Limited Bonase Electronics (HK) Co., Limited
Part Number:
STM8S103F3P6TR
Manufacturer:
EXAR
Quantity:
132
Price:
Company:
Bonase Electronics (HK) Co., Limited Bonase Electronics (HK) Co., Limited
Part Number:
STM8S103F3U6TR
Manufacturer:
MAXIM
Quantity:
1 400
Price:
STM8S103K3 STM8S103F3 STM8S103F2
5.3
(1)
maximum ratings.
(2)
state of PA1 is not driven. It is recommended to use PA1 only in input mode if halt/active-halt is used in the application.
(3)
I/O pins used simultaneously for high current source/sink must be uniformly spaced around the package. In addition, the total driven current must respect the absolute
When the MCU is in halt/active-halt mode, PA1 is automatically configured in input weak pull-up and cannot be used for waking up the device. In this mode, the output
In the open-drain output column, "T" defines a true open-drain I/O (P-buffer, weak pull-up, and protection diode to V DD are not implemented).
Alternate function remapping
As shown in the rightmost column of the pin description table, some alternate functions can
be remapped at different I/O ports by programming one of eight AFR (alternate function
remap) option bits. When the remapping option is active, the default alternate function is no
longer available.
To use an alternate function, the corresponding peripheral must be enabled in the peripheral
registers.
Alternate function remapping does not effect GPIO capabilities of the I/O ports (see the GPIO
section of the family reference manual, RM0016).
DocID15441 Rev 7
Pinout and pin description
25/113

Related parts for STM8S103F3