STM8S103F3 STMicroelectronics, STM8S103F3 Datasheet - Page 48

no-image

STM8S103F3

Manufacturer Part Number
STM8S103F3
Description
Access line, 16 MHz STM8S 8-bit MCU, up to 8 Kbytes Flash, data EEPROM
Manufacturer
STMicroelectronics
Datasheet

Specifications of STM8S103F3

Program Memory
8 Kbytes Flash; data retention 20 years at 55 °C after 10 kcycles
Data Memory
640 bytes true data EEPROM; endurance 300 kcycles
Ram
1 Kbytes
Advanced Control Timer
16-bit, 4 CAPCOM channels, 3 complementary outputs, dead-time insertion and flexible synchronization

Available stocks

Company
Part Number
Manufacturer
Quantity
Price
Company:
Bonase Electronics (HK) Co., Limited Bonase Electronics (HK) Co., Limited
Part Number:
STM8S103F3M6
Manufacturer:
FSC
Quantity:
4 500
Price:
Company:
Bonase Electronics (HK) Co., Limited Bonase Electronics (HK) Co., Limited
Part Number:
STM8S103F3M6TR
Manufacturer:
SONY
Quantity:
12 500
Price:
Company:
Bonase Electronics (HK) Co., Limited Bonase Electronics (HK) Co., Limited
Part Number:
STM8S103F3P3
Manufacturer:
ON
Quantity:
3 206
Price:
Company:
Bonase Electronics (HK) Co., Limited Bonase Electronics (HK) Co., Limited
Part Number:
STM8S103F3P3TR
Manufacturer:
STMicroelectronics
Quantity:
2 000
Price:
Company:
Bonase Electronics (HK) Co., Limited Bonase Electronics (HK) Co., Limited
Part Number:
STM8S103F3P6
Manufacturer:
ST
Quantity:
3 000
Price:
Company:
Bonase Electronics (HK) Co., Limited Bonase Electronics (HK) Co., Limited
Part Number:
STM8S103F3P6.
Manufacturer:
ST
Quantity:
15 000
Price:
Company:
Bonase Electronics (HK) Co., Limited Bonase Electronics (HK) Co., Limited
Part Number:
STM8S103F3P6TR
Manufacturer:
EXAR
Quantity:
132
Price:
Company:
Bonase Electronics (HK) Co., Limited Bonase Electronics (HK) Co., Limited
Part Number:
STM8S103F3U6TR
Manufacturer:
MAXIM
Quantity:
1 400
Price:
Electrical characteristics
10
10.1
10.1.1
10.1.2
10.1.3
10.1.4
48/113
Electrical characteristics
Parameter conditions
Unless otherwise specified, all voltages are referred to V
Minimum and maximum values
Unless otherwise specified the minimum and maximum values are guaranteed in the worst
conditions of ambient temperature, supply voltage and frequencies by tests in production on
100 % of the devices with an ambient temperature at T
the selected temperature range).
Data based on characterization results, design simulation and/or technology characteristics
are indicated in the table footnotes and are not tested in production. Based on characterization,
the minimum and maximum values refer to sample tests and represent the mean value plus
or minus three times the standard deviation (mean ± 3 Σ).
Typical values
Unless otherwise specified, typical data are based on T
only as design guidelines and are not tested.
Typical ADC accuracy values are determined by characterization of a batch of samples from
a standard diffusion lot over the full temperature range, where 95% of the devices have an
error less than or equal to the value indicated (mean ± 2 Σ).
Typical curves
Unless otherwise specified, all typical curves are given only as design guidelines and are not
tested.
Loading capacitor
The loading conditions used for pin parameter measurement are shown in the following figure.
Figure 7: Pin loading conditions
DocID15441 Rev 7
50 pF
STM8S103K3 STM8S103F3 STM8S103F2
STM8 PIN
A
A
SS
= 25 °C and T
= 25 °C, V
.
DD
= 5 V. They are given
A
= T
Amax
(given by

Related parts for STM8S103F3