ST7LITE49K2 STMicroelectronics, ST7LITE49K2 Datasheet - Page 82
ST7LITE49K2
Manufacturer Part Number
ST7LITE49K2
Description
8-bit MCU
Manufacturer
STMicroelectronics
Datasheet
1.ST7LITE49K2.pdf
(245 pages)
Specifications of ST7LITE49K2
8 Kbytes Single Voltage Extended Flash (xflash) Program Memory With Read-out Protection In-circuit Programming And In-application Programming (icp And Iap) Endurance
10K write/erase cycles guaranteed Data retention
256 Bytes Data Eeprom With Read-out Protection. 300k Write/erase Cycles Guaranteed, Data Retention
20 years at 55 °C.
Clock Sources
Internal trimmable 8 MHz RC oscillator, auto-wakeup internal low power - low frequency oscillator, crystal/ceramic resonator or external clock
Five Power Saving Modes
Halt, Active-halt, Auto-wakeup from Halt, Wait and Slow
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
- Current page: 82 of 245
- Download datasheet (4Mb)
On-chip peripherals
11.1.4
11.1.5
82/245
The application program must write in the CR register at regular intervals during normal
operation to prevent an MCU reset. This downcounter is free-running: it counts down even if
the watchdog is disabled. The value to be stored in the CR register must be between FFh
and C0h (see
●
●
●
Following a reset, the watchdog is disabled. Once activated it cannot be disabled, except by
a reset.
The T6 bit can be used to generate a software reset (the WDGA bit is set and the T6 bit is
cleared).
If the watchdog is activated, the HALT instruction will generate a Reset.
Table 33.
1. The timing variation shown in
2. The number of CPU clock cycles applied during the Reset phase (256 or 4096) must be taken into account
Hardware watchdog option
If Hardware Watchdog is selected by option byte, the watchdog is always active and the
WDGA bit in the CR is not used.
Refer to the option byte description in
Using Halt mode with the WDG (WDGHALT option)
If Halt mode with Watchdog is enabled by option byte (No watchdog reset on HALT
instruction), it is recommended before executing the HALT instruction to refresh the WDG
counter, to avoid an unexpected WDG reset immediately after waking up the microcontroller.
Same behavior in active-halt mode.
Interrupts
None.
CR register.
in addition to these timings.
The WDGA bit is set (watchdog enabled)
The T6 bit is set to prevent generating an immediate reset
The T[5:0] bits contain the number of increments which represents the time delay
before the watchdog produces a reset.
counter code
Watchdog timing
WDG
Table 33: Watchdog
C0h
FFh
Table 33
(1)(2)
timing):
is due to the unknown status of the prescaler when writing to the
Section 14 on page
f
CPU
= 8 MHz
[ms]
min
127
1
230.
[ms]
max
128
2
ST7LITE49K2
Related parts for ST7LITE49K2
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
STMicroelectronics [RIPPLE-CARRY BINARY COUNTER/DIVIDERS]
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
STMicroelectronics [LIQUID-CRYSTAL DISPLAY DRIVERS]
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
BOARD EVAL FOR MEMS SENSORS
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
NPN TRANSISTOR POWER MODULE
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
TURBOSWITCH ULTRA-FAST HIGH VOLTAGE DIODE
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
DIODE / SCR MODULE
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
DIODE / SCR MODULE
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
Search -----> STE16N100
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
Search ---> STE53NA50
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
NPN Transistor Power Module
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
DIODE / SCR MODULE
Manufacturer:
STMicroelectronics
Datasheet: