AD6426 Analog Devices, AD6426 Datasheet - Page 10

• Manufacturer Part Number: AD6426
• Description: Enhanced GSM Processor
• Manufacturer: Analog Devices

This Information applies to a product under development. Its characteristics and specifications are subject to change without notice. Analog Devices assumes no
obligation regarding future manufacture unless otherwise agreed to in writing. No responsibility is assumed by Analog Devices for its use; nor for any
infringements of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent
rights of Analog Devices.
Revision Preliminary 2.3 (June 9, ´98)
Preliminary Technical Information
10
28
29
30
35
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
72
73
74
75
76
77
78
79
88
#
0
2
4
5
6
7
8
9
Enable Polarity
Autocalibrate
GPO11 Data
Synthesizer
Synthesizer
Tx Monitor
Polarity
Enable
Isolate
TxPA
7
BAND ENABLE
Config. Dynam.
INT COUNT[8]
Power Control
GPO11 Select
Coprocessor
Enable Type
GPO19 Sel
EVBC Read
Synthesizer
Synthesizer
Tx Phase
Polarity
6
Backlight Duty Cycle
Rx Radio Control
OCE OVERRIDE
Disable Synth.1
Interface active
GPIO9 OP En
Clock Polarity
Output Clock
IRQ5 Enable
GPO18 Sel
Synthesizer
Synthesizer
IRQ5 active
Backlight 1
Polarity
Enable
5
Table 2. CC Control Register Contents
Test Data Enable
Tx Radio Control
Interrupt Counter
Disable Synth. 0 Synt. Enable Sel.
EEPROM Data
Output Enable
Tx Data Delay
INT CNT RST
GPIO8 OP En
IRQ4 Enable
GPO17 Sel
IRQ4 active
NMI Select
GP Power
Override
Polarity
Control
4
- 10 -
TW ( 7 : 0 )
TD ( 7 : 0 )
EVBC Serial Port ( 15 : 8 )
EVBC Serial Port ( 7 : 0 )
Synthesizer (31: 24)
Synthesizer (23: 16)
Synthesizer (15: 8)
Synthesizer (7: 0)
EVBC Tx Address
Calibrate Radio
Autocalibration
GPO10 Data
EVBC Reset
IRQ3 Enable
Error Count
IRQ3 active
Tx PHASE
Encryption
SW-Reset
SW-Reset
Version
Decode
Enable
Base Station Identity Code
Type
3
Keypad Row
Synthesizer Bit Count
Interrupt Counter
Encryption Type
Load Dynamic 1
Synth. Interface
EVBC Interface
GPO10 Select
Power Enable
Traffic Frame
IRQ2 Enable
Deinterleave
Synthesizer
DSP Power
IRQ2 active
DSP Reset
Modulate 1
Synt. Mode
SW-Reset
SW-Reset
EERPOM
GPO19
Monitor
Control
Enable
Enable
Clock
2
Keypad Column
Training Sequence Code
EVBC Rx-Buff. full EVBC Tx-Buf.empty
Encrypt Key Load
FLASHPWD dis.
Confidential Information
Data Ser. Select
Load Dynamic 2
DSP Interface
Power Enable
DSP Interface
Radio Power
GPIO9 Data
Synthesizer
Decryption
SW-Reset
SW-Reset
EEPROM
interleave
Backlight LED Control
Receive
GPO18
Control
Enable
Enable
Enable
1
TW ( 9 : 8 )
TD ( 9 : 8 )
Pin Mode
Synthes. Interface
AD6426
Encryption Power
NMI Edge Pol.
GPIO8 Data
Synthesizer
DAIRESET
Encryption
SW-Reset
SW-Reset
CC Reset
EERPOM
Transmit
GPO17
Encode
Enable
Enable
Enable
Clock
Data
0