PIC18F25J50 MICROCHIP [Microchip Technology], PIC18F25J50 Datasheet - Page 33
![no-image](/images/no-image-200.jpg)
PIC18F25J50
Manufacturer Part Number
PIC18F25J50
Description
28/44-Pin, Low-Power, High-Performance USB Microcontrollers with nanoWatt XLP Technology
Manufacturer
MICROCHIP [Microchip Technology]
Datasheet
1.PIC18F25J50.pdf
(562 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
PIC18F25J50-I/SO
Manufacturer:
MICROCHIP
Quantity:
1 001
Company:
Part Number:
PIC18F25J50-I/SP
Manufacturer:
MICROCHIP
Quantity:
1 001
Company:
Part Number:
PIC18F25J50-I/SS
Manufacturer:
MICROCHIP
Quantity:
1 001
Company:
Part Number:
PIC18F25J50T-I/SO
Manufacturer:
MICROCHIP
Quantity:
1 001
Company:
Part Number:
PIC18F25J50T-I/SS
Manufacturer:
MICROCHIP
Quantity:
1 001
- Current page: 33 of 562
- Download datasheet (5Mb)
2.6
Many microcontrollers have options for at least two
oscillators: a high-frequency primary oscillator and a
low-frequency
Section 3.0 “Oscillator Configurations”
The oscillator circuit should be placed on the same
side of the board as the device. Place the oscillator
circuit close to the respective oscillator pins with no
more than 0.5 inch (12 mm) between the circuit
components and the pins. The load capacitors should
be placed next to the oscillator itself, on the same side
of the board.
Use a grounded copper pour around the oscillator cir-
cuit to isolate it from surrounding circuits. The
grounded copper pour should be routed directly to the
MCU ground. Do not run any signal traces or power
traces inside the ground pour. Also, if using a two-sided
board, avoid any traces on the other side of the board
where the crystal is placed.
Layout suggestions are shown in
packages may be handled with a single-sided layout
that completely encompasses the oscillator pins. With
fine-pitch packages, it is not always possible to com-
pletely surround the pins and components. A suitable
solution is to tie the broken guard sections to a mirrored
ground layer. In all cases, the guard trace(s) must be
returned to ground.
In planning the application’s routing and I/O assign-
ments, ensure that adjacent port pins, and other
signals in close proximity to the oscillator, are benign
(i.e., free of high frequencies, short rise and fall times,
and other similar noise).
For additional information and design guidance on
oscillator circuits, please refer to these Microchip
Application Notes, available at the corporate web site
(www.microchip.com):
• AN826, “Crystal Oscillator Basics and Crystal
• AN849, “Basic PICmicro
• AN943, “Practical PICmicro
• AN949, “Making Your Oscillator Work”
2.7
Unused I/O pins should be configured as outputs and
driven to a logic low state. Alternatively, connect a 1 kΩ
to 10 kΩ resistor to V
output to logic low.
2011 Microchip Technology Inc.
Selection for rfPIC™ and PICmicro
and Design”
External Oscillator Pins
Unused I/Os
secondary
SS
on unused pins and drive the
®
Oscillator Design”
®
oscillator
Oscillator Analysis
Figure
®
Devices”
for details).
2-5. In-line
(refer
to
PIC18F46J50 FAMILY
FIGURE 2-5:
(tied to ground)
Timer1 Oscillator
Bottom Layer
Copper Pour
Oscillator
GND
Primary
Crystal
OSCO
OSCI
C1
C2
T1 Oscillator: C1
DEVICE PINS
Single-Sided and In-Line Layouts:
Fine-Pitch (Dual-Sided) Layouts:
(tied to ground)
Copper Pour
SUGGESTED PLACEMENT
OF THE OSCILLATOR
CIRCUIT
Top Layer Copper Pour
`
`
(tied to ground)
`
Primary Oscillator
T1 Oscillator: C2
Crystal
DEVICE PINS
DS39931D-page 33
C2
C1
Oscillator
Crystal
OSC1
OSC2
GND
T1OSO
T1OS I
Related parts for PIC18F25J50
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
![PIC18F-LF1XK50](/images/no-image3.png)
Part Number:
Description:
20-Pin USB Flash Microcontrollers
Manufacturer:
MICROCHIP [Microchip Technology]
Datasheet:
![PIC18F6393T-I/PT](/photos/6/81/68123/c04-066_pf_tmb.jpg)
Part Number:
Description:
PIC18F With 128-segment LCD Driver And 12-bit ADC, 8KB Flash, 768B RAM, CCP, MSS
Manufacturer:
Microchip Technology
Datasheet:
![PIC18F6493T-I/PT](/photos/6/81/68123/c04-066_pf_tmb.jpg)
Part Number:
Description:
PIC18F With 128-segment LCD Driver And 12-bit ADC, 16KB Flash, 768B RAM, CCP, MS
Manufacturer:
Microchip Technology
Datasheet:
![PIC18F8393T-I/PT](/images/manufacturer_photos/0/4/439/microchip_technology_tmb.jpg)
Part Number:
Description:
PIC18F With 192-segment LCD Driver And 12-bit ADC, 8KB Flash, 768B RAM, CCP, MSS
Manufacturer:
Microchip Technology
Datasheet:
![PIC18F8493T-I/PT](/images/manufacturer_photos/0/4/439/microchip_technology_tmb.jpg)
Part Number:
Description:
PIC18F With 192-segment LCD Driver And 12-bit ADC, 16KB Flash, 768B RAM, CCP, MS
Manufacturer:
Microchip Technology
Datasheet:
![PIC18F6585-I/L](/photos/16/12/161282/68-plcc-large-300dpi-lyrd_tmb.jpg)
Part Number:
Description:
Microcontrollers (MCU) 48KB 3328 RAM 52 I/O
Manufacturer:
Microchip Technology
Datasheet:
![PIC18F6680-I/L](/photos/16/12/161282/68-plcc-large-300dpi-lyrd_tmb.jpg)
Part Number:
Description:
Microcontrollers (MCU) 64KB 3328 RAM 52 I/O
Manufacturer:
Microchip Technology
Datasheet:
![PIC18F65K90T-I/MR](/photos/16/3/160368/qfn64_tmb.jpg)
Part Number:
Description:
32kB Flash, 2kB RAM, 1kB EE, NanoWatt XLP, LCD 64 QFN 9x9x0.9mm T/R
Manufacturer:
Microchip Technology
Datasheet:
![PIC18F65K90T-I/PT](/photos/16/3/160367/tqfp-64_tmb.jpg)
Part Number:
Description:
32kB Flash, 2kB RAM, 1kB EE, NanoWatt XLP, LCD 64 TQFP 10x10x1mm T/R
Manufacturer:
Microchip Technology
Datasheet:
![PIC18F87K90T-I/PT](/photos/40/31/403173/tqfp-80_tmb.jpg)
Part Number:
Description:
128kB Flash, 4kB RAM, 1kB EE, 16MIPS, NanoWatt XLP, LCD, 5V 80 TQFP 12x12x1mm T/
Manufacturer:
Microchip Technology
Datasheet:
![PIC18F65K90-I/MR](/photos/16/3/160368/qfn64_tmb.jpg)
Part Number:
Description:
32kB Flash, 2kB RAM, 1kB EE, NanoWatt XLP, LCD 64 QFN 9x9x0.9mm TUBE
Manufacturer:
Microchip Technology
Datasheet:
![PIC18F65K90-I/PT](/photos/16/3/160367/tqfp-64_tmb.jpg)
Part Number:
Description:
32kB Flash, 2kB RAM, 1kB EE, NanoWatt XLP, LCD 64 TQFP 10x10x1mm TRAY
Manufacturer:
Microchip Technology
![PIC18F87K90-I/PT](/photos/40/31/403173/tqfp-80_tmb.jpg)
Part Number:
Description:
128kB Flash, 4kB RAM, 1kB EE, 16MIPS, NanoWatt XLP, LCD, 5V 80 TQFP 12x12x1mm TR
Manufacturer:
Microchip Technology
![PIC1-100-JT](/images/no-image3.png)
Part Number:
Description:
SURFACE MOUNT POWER INDUCTORS
Manufacturer:
RCD [RCD COMPONENTS INC.]
Datasheet: