HD6417706 RENESAS [Renesas Technology Corp], HD6417706 Datasheet - Page 271

no-image

HD6417706

Manufacturer Part Number
HD6417706
Description
Renesas 32-Bit RISC Microcomputer Super RISC engine Family/SH7700 Series
Manufacturer
RENESAS [Renesas Technology Corp]
Datasheet

Available stocks

Company
Part Number
Manufacturer
Quantity
Price
Part Number:
HD6417706
Manufacturer:
TDK
Quantity:
500
Part Number:
HD6417706
Manufacturer:
TOSH
Quantity:
1 000
Part Number:
HD6417706-SH3-133V
Manufacturer:
RENESAS/瑞萨
Quantity:
20 000
Part Number:
HD6417706BP133
Manufacturer:
RENESAS/瑞萨
Quantity:
20 000
Part Number:
HD6417706BP133V
Manufacturer:
HITACHI/日立
Quantity:
20 000
Part Number:
HD6417706F120DV
Manufacturer:
HITACHI
Quantity:
96
Part Number:
HD6417706F120DV
Manufacturer:
RENESAS/PBF
Quantity:
375
Part Number:
HD6417706F120DV
Manufacturer:
RENESAS/瑞萨
Quantity:
20 000
Part Number:
HD6417706F133
Manufacturer:
RENESAS/瑞萨
Quantity:
20 000
Part Number:
HD6417706F133V
Manufacturer:
EDISON
Quantity:
2 000
Part Number:
HD6417706F133V
Manufacturer:
Renesas Electronics America
Quantity:
10 000
Company:
Part Number:
HD6417706F133V
Quantity:
27
In order to use synchronous DRAM, mode setting must first be performed after powering on. To
perform synchronous DRAM initialization correctly, the bus state controller registers must first be
set, followed by a write to the synchronous DRAM mode register. In synchronous DRAM mode
register setting, the address signal value at that time is latched by a combination of the RAS, CAS,
and RD/WR signals. If the value to be set is X, the bus state controller provides for value X to be
written to the synchronous DRAM mode register by performing a write to address H'FFFFD000 +
X for area 2 synchronous DRAM, and to address H'FFFFE000 + X for area 3 synchronous
DRAM. In this operation the data is ignored, but the mode write is performed as a byte-size
access. To set burst read/single write, CAS latency 1 to 3, wrap type = sequential, and burst length
1 supported by this LSI, arbitrary data is written in a byte-size access to the following addresses.
Mode register setting timing is shown in figure 8.27.
As a result of the write to address H'FFFFD000 + X or H'FFFFE000 + X, a precharge all banks
(PALL) command is first issued in the TRp1 cycle, then a mode register write command is issued
in the TMw1 cycle.
Address signals, when the mode-register write command is issued, are as follows:
Power-On Sequence
32-bit
Bus width
16-bit
Bus width
32-bit
Bus width
16-bit
Bus width
CAS latency 1
CAS latency 2
CAS latency 3
CAS latency 1
CAS latency 2
CAS latency 3
A15 to A9
A8 to A6
A5
A4 to A2
A14 to A8
A7 to A5
A4
A3 to A1
Area 2
FFFFD840
FFFFD880
FFFFD8C0
Area 2
FFFFD420
FFFFD440
FFFFD460
0000100 (burst read and single write)
CAS latency
0 (burst type = sequential)
000 (burst length 1)
0000100 (burst read and single write)
CAS latency
0 (burst type = sequential)
000 (burst length 1)
Area 3
FFFFE840
FFFFE880
FFFFE8C0
Area 3
FFFFE420
FFFFE440
FFFFE460
Rev. 4.00, 03/04, page 225 of 660

Related parts for HD6417706