UPSD3254 STMICROELECTRONICS [STMicroelectronics], UPSD3254 Datasheet - Page 44

no-image

UPSD3254

Manufacturer Part Number
UPSD3254
Description
Flash Programmable System Devices with 8032 Microcontroller Core
Manufacturer
STMICROELECTRONICS [STMicroelectronics]
Datasheet

Available stocks

Company
Part Number
Manufacturer
Quantity
Price
Part Number:
UPSD3254A-24U6
Manufacturer:
ST
0
Part Number:
UPSD3254A-40T6
Manufacturer:
STMicroelectronics
Quantity:
10 000
Part Number:
UPSD3254A-40U6
Manufacturer:
STMicroelectronics
Quantity:
10 000
Part Number:
UPSD3254A-40U6
Manufacturer:
ST
Quantity:
20 000
Part Number:
UPSD3254B-24U6
Manufacturer:
ST
0
Part Number:
UPSD3254BV-24U6
Manufacturer:
ST
Quantity:
3 100
Part Number:
UPSD3254BV-24U6
Manufacturer:
ST
Quantity:
875
Part Number:
UPSD3254BV-24U6
Manufacturer:
STMicroelectronics
Quantity:
10 000
Part Number:
UPSD3254BV-24U6
Manufacturer:
ST
Quantity:
20 000
Part Number:
UPSD3254BV-40U6
Manufacturer:
ST
Quantity:
200
UPSD3254A, UPSD3254BV, UPSD3253B, UPSD3253BV
How Interrupts are Handled
The interrupt flags are sampled at S5P2 of every
machine cycle. The samples are polled during fol-
lowing machine cycle. If one of the flags was in a
set condition at S5P2 of the preceding cycle, the
polling cycle will find it and the interrupt system will
generate an LCALL to the appropriate service rou-
tine, provided this H/W generated LCALL is not
blocked by any of the following conditions:
The polling cycle is repeated with each machine
cycle, and the values polled are the values that
were present at S5P2 of the previous machine cy-
cle.
Note: If an interrupt flag is active but being re-
sponded to for one of the above mentioned condi-
tions, if the flag is still inactive when the blocking
condition is removed, the denied interrupt will not
be serviced. In other words, the fact that the inter-
rupt flag was once active but not serviced is not re-
membered. Every polling cycle is new.
The processor acknowledges an interrupt request
by executing a hardware generated LCALL to the
appropriate service routine. The hardware gener-
ated LCALL pushes the contents of the Program
Counter on to the stack (but it does not save the
PSW) and reloads the PC with an address that de-
44/175
An interrupt of equal priority or higher priority
level is already in progress.
The current machine cycle is not the final cycle
in the execution of the instruction in progress.
The instruction in progress is RETI or any
access to the interrupt priority or interrupt
enable registers.
pends on the source of the interrupt being vec-
tored to as shown in Table 24.
Execution proceeds from that location until the
RETI instruction is encountered. The RETI instruc-
tion informs the processor that the interrupt routine
is no longer in progress, then pops the top two
bytes from the stack and reloads the Program
Counter. Execution of the interrupted program
continues from where it left off.
Note: A simple RET instruction would also return
execution to the interrupted program, but it would
have left the interrupt control system thinking an
interrupt was still in progress, making future inter-
rupts impossible.
Table 24. Vector Addresses
Timer 2+EXF2
2nd USART
1st USART
Source
Timer 0
Timer 1
DDC
USB
Int0
Int1
I²C
Vector Address
004Bh
000Bh
003Bh
001Bh
002Bh
0003h
0043h
0013h
0033h
0023h

Related parts for UPSD3254