TE28F008xxx Intel Corporation, TE28F008xxx Datasheet - Page 16

• Manufacturer Part Number: TE28F008xxx
• Description: (TE28F Series) 3 Volt Advanced Boot Block Flash Memory
• Manufacturer: Intel Corporation

28F004/400B3, 28F008/800B3, 28F016/160B3, 28F320B3, 28F640B3
10
00, 01,
60, 2F,
C0, 98
Code
Table 4.
D0
FF
40
10
20
B0
70
50
90
Program Set-Up
Program Set-Up
Program / Erase
Program / Erase
Erase Confirm
Read Identifier
Device Mode
Erase Set-Up
Read Status
Clear Status
Read Array
When the device is in read array mode, four control signals control data output:
In addition, the address of the desired location must be applied to the address pins. If the device is
not in read array mode, as would be the case after a program or erase operation, the Read Array
command (FFH) must be written to the CUI before array reads can take place.
Command Codes and Descriptions
Reserved
NOTE: See
Alternate
Suspend
Resume
Register
Register
Invalid/
•
•
•
•
WE# must be logic high (V
CE# must be logic low (V
OE# must be logic low (V
RP# must be logic high (V
Appendix A
Unassigned commands that should not be used. Intel reserves the right to redefine these
codes for future functions.
Places the device in read array mode, such that array data will be output on the data pins.
This is a two-cycle command. The first cycle prepares the CUI for a program operation. The
second cycle latches addresses and data information and initiates the WSM to execute the
Program algorithm. The flash outputs status register data when CE# or OE# is toggled. A Read
Array command is required after programming to read array data. See
(See 40H/Program Set-Up)
Prepares the CUI for the Erase Confirm command. If the next command is not an Erase
Confirm command, then the CUI will (a) set both SR.4 and SR.5 of the status register to a “1,”
(b) place the device into the read status register mode, and (c) wait for another command. See
Section
If the previous command was an Erase Set-Up command, then the CUI will close the address
and data latches, and begin erasing the block indicated on the address pins. During erase, the
device will only respond to the Read Status Register and Erase Suspend commands. The
device will output status register data when CE# or OE# is toggled.
If a program or erase operation was previously suspended, this command will resume that
operation
Issuing this command will begin to suspend the currently executing program/erase operation.
The status register will indicate when the operation has been successfully suspended by
setting either the program suspend (SR.2) or erase suspend (SR.6) and the WSM status bit
(SR.7) to a “1” (ready). The WSM will continue to idle in the SUSPEND state, regardless of the
state of all input control pins except RP#, which will immediately shut down the WSM and the
remainder of the chip if it is driven to V
This command places the device into read status register mode. Reading the device will output
the contents of the status register, regardless of the address presented to the device. The
device automatically enters this mode after a program or erase operation has been initiated.
See
The WSM can set the block lock status (SR.1) , V
erase status (SR.5) bits in the status register to “1,” but it cannot clear them to “0.” Issuing this
command clears those bits to “0.”
Puts the device into the intelligent identifier read mode, so that reading the device will output
the manufacturer and device codes (A
address inputs must be 0). See Section
Section
3.2.5.
for mode transition information.
3.2.3.
IL
IL
IH
IH
)
)
)
)
0
IL
= 0 for manufacturer, A
. See
Section
Description
Section 3.2.4.1
3.2.2.
PP
status (SR.3), program status (SR.4), and
and
0
= 1 for device, all other
Section
Section
3.2.4.1.
3.2.4.
3UHOLPLQDU\