S25FL512SAGMFIG13 Spansion, S25FL512SAGMFIG13 Datasheet - Page 19

• Manufacturer Part Number: S25FL512SAGMFIG13
• Description: Flash 512Mb 3V 133MHz Serial NOR Flash
• Manufacturer: Spansion

Specifications of S25FL512SAGMFIG13

• Rohs: yes
• Memory Type: Flash
• Memory Size: 512 MB
• Architecture: Uniform
• Timing Type: Asynchronous
• Interface Type: SPI
• Supply Voltage - Max: 3.6 V
• Supply Voltage - Min: 2.7 V
• Operating Temperature: - 40 C to + 85 C
• Mounting Style: SMD/SMT
• Package / Case: SO-16

3.10
3.11
3.12
3.13
3.14
June 13, 2012 S25FL512S_00_04
Core Voltage Supply (V
Versatile I/O Power Supply (V
Supply and Signal Ground (V
Not Connected (NC)
Reserved for Future Use (RFU)
SI_or_IO_(during_input)
The HOLD# signal has an internal pull-up resistor and may be left unconnected in the host system if not used
for Quad mode.
V
functions including read, program, and erase. The voltage may vary from 2.7V to 3.6V.
The Versatile I/O (V
the host system to set the voltage levels that the device tolerates on all inputs and drives on outputs (address,
control, and IO signals). The V
For example, a V
to and from other 1.8V, 2.5V or 3V devices on the same data bus. V
signals operate at the same voltage as the core of the device. V
when not available the V
During the rise of power supplies the V
voltage. However, the V
> 1.65V, i.e. the V
power up, until the V
This supply is not available in all package options. For a backward compatible SO16 footprint, the V
is tied to V
V
drivers.
No device internal signal is connected to the package connector nor is there any future plan to use the
connector for a signal. The connection may safely be used for routing space for a signal on a Printed Circuit
Board (PCB). However, any signal connected to an NC must not have voltage levels higher than V
No device internal signal is currently connected to the package connector but is there potential future use of
the connector. It is recommended to not use RFU connectors for PCB routing channels so that the PCB may
take advantage of future enhanced features in compatible footprint devices.
SO_or_IO_(external)
SO_or_IO_(internal)
CC
SS
is the common voltage drain and ground reference for the device core, input signal receivers, and output
is the voltage source for all device internal logic. It is the single voltage used for all device internal
CC
D a t a
inside the package; thus, the IO will function at V
HOLD#
SCK
CS#
IO
IO
IO
of 1.65V - 3.6V allows for I/O at the 1.8V, 2.5V or 3V levels, driving and receiving signals
supply voltage must not lag behind the V
IO
) supply is the voltage source for all device input receivers and output drivers and allows
S h e e t
supply voltage reaches its minimum operating level.
IO
IO
supply voltage must also be above V
supply is tied to V
Figure 3.1 HOLD Mode Operation
Valid Input
CC
IO
)
range is 1.65V to V
A
( P r e l i m i n a r y )
A
SS
IO
IO
S25FL512S
B
)
supply voltage must remain less than or equal to the V
)
Hold Condition
Standard Use
Don't Care
CC
internal to the package.
B
CC
. V
IO
Valid Input
B
cannot be greater than V
CC
CC
CC
IO
supply voltage by more than 200 mV during
C
level.
C
is not available in all package options,
-200 mV until the V
IO
may be tied to V
Hold Condition
Non-standard Use
Don't Care
D
CC
IO
Valid Input
CC
.
supply voltage is
D
so that interface
E
E
CC
IO
supply
IO
.
supply
19