MPC8313E-RDB Freescale Semiconductor, MPC8313E-RDB Datasheet - Page 38
![BOARD PROCESSOR](/photos/9/23/92379/mfg_mpc8313e-rdb_sml.jpg)
MPC8313E-RDB
Manufacturer Part Number
MPC8313E-RDB
Description
BOARD PROCESSOR
Manufacturer
Freescale Semiconductor
Series
PowerQUICC II™ PROr
Type
MCUr
Datasheets
1.MPC8313CZQAFFB.pdf
(100 pages)
2.MPC8313E-RDBB.pdf
(52 pages)
3.MPC8313E-RDBB.pdf
(2 pages)
Specifications of MPC8313E-RDB
Contents
Reference Design Board, Software and Documentation
Termination Type
SMD
Supply Voltage Max
1.05V
Tool / Board Applications
Wired Connectivity-LIN, CAN, Ethernet, USB
Mcu Supported Families
POWERQUICC II PRO
Rohs Compliant
Yes
Filter Terminals
SMD
Silicon Manufacturer
Freescale
Silicon Core Number
MPC83xx
Kit Application Type
Communication & Networking
Application Sub Type
Ethernet
Core Architecture
Power Architecture
Silicon Family Name
PowerQUICC II PRO
For Use With/related Products
MPC8313E
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
High-Speed Serial Interfaces (HSSI)
9.2
The SerDes reference clock inputs are applied to an internal PLL whose output creates the clock used by
the corresponding SerDes lanes. The SerDes reference clocks input is SD_REF_CLK and SD_REF_CLK
for SGMII interface.
The following sections describe the SerDes reference clock requirements and some application
information.
9.2.1
Figure 23
38
•
•
•
•
The supply voltage requirements for XCOREV
SerDes reference clock receiver reference circuit structure:
— The SD_REF_CLK and SD_REF_CLK are internally AC-coupled differential inputs as shown
— The external reference clock driver must be able to drive this termination.
— The SerDes reference clock input can be either differential or single-ended. Refer to the
The maximum average current requirement that also determines the common mode voltage range:
— When the SerDes reference clock differential inputs are DC coupled externally with the clock
— This current limitation sets the maximum common mode input voltage to be less than 0.4 V
— If the device driving the SD_REF_CLK and SD_REF_CLK inputs cannot drive 50 Ω to
The input amplitude requirement. This requirement is described in detail in the following sections.
SerDes Reference Clocks
shows a receiver reference diagram of the SerDes reference clocks.
in
termination to XCOREV
differential mode and single-ended mode description below for further detailed requirements.
driver chip, the maximum average current allowed for each input pin is 8 mA. In this case, the
exact common mode input voltage is not critical as long as it is within the range allowed by the
maximum average current of 8 mA (refer to the following bullet for more detail), since the
input is AC-coupled on-chip.
(0.4 V/50 = 8 mA) while the minimum common mode input level is 0.1 V above XCOREV
For example, a clock with a 50/50 duty cycle can be produced by a clock driver with output
driven by its current source from 0 to 16 mA (0–0.8 V), such that each phase of the differential
input has a single-ended swing from 0 V to 800 mV with the common mode voltage at 400 mV.
XCOREV
AC-coupled off-chip.
SerDes Reference Clock Receiver Characteristics
Figure
MPC8313E PowerQUICC
23. Each differential clock input (SD_REF_CLK or SD_REF_CLK) has a 50-Ω
SS
DC, or it exceeds the maximum input current limitations, then it must be
SS
followed by on-chip AC coupling.
™
II Pro Processor Hardware Specifications, Rev. 3
DD
are specified in
Table 1
and
Freescale Semiconductor
Table
2.
SS
.