PIC18LF25K22-I/SP Microchip Technology, PIC18LF25K22-I/SP Datasheet - Page 164

• Manufacturer Part Number: PIC18LF25K22-I/SP
• Description: MCU 8BIT 32KB FLASH 3.6V 28SDIP
• Manufacturer: Microchip Technology
• Series: PIC® XLP™ 18Fr

Specifications of PIC18LF25K22-I/SP

• Program Memory Type: FLASH
• Program Memory Size: 32KB (16K x 16)
• Package / Case: 28-DIP (0.300", 7.62mm)
• Core Processor: PIC
• Core Size: 8-Bit
• Speed: 64MHz
• Connectivity: I²C, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, HLVD, POR, PWM, WDT
• Number Of I /o: 24
• Eeprom Size: 256 x 8
• Ram Size: 1.5K x 8
• Voltage - Supply (vcc/vdd): 1.8 V ~ 3.6 V
• Data Converters: A/D 19x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Processor Series: PIC18LF
• Core: PIC
• Data Bus Width: 8 bit
• Data Ram Size: 1536 B
• Interface Type: I2C, SPI, EUSART
• Maximum Clock Frequency: 64 MHz
• Number Of Programmable I/os: 25
• Number Of Timers: 7
• Operating Supply Voltage: 1.8 V to 3.6 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: Through Hole
• 3rd Party Development Tools: 52715-96, 52716-328, 52717-734, 52712-325, EWPIC18
• Development Tools By Supplier: PG164130, DV164005
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10 bit, 17 Channel
• On-chip Dac: 5 bit
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Lead free / RoHS Compliant

PIC18(L)F2X/4XK22
FIGURE 12-2:
12.7
Timer1/3/5 can be configured to count freely or the
count can be enabled and disabled using Timer1/3/5
Gate circuitry. This is also referred to as Timer1/3/5
Gate Enable.
Timer1/3/5 Gate can also be driven by multiple
selectable sources.
12.7.1
The Timer1/3/5 Gate Enable mode is enabled by
setting the TMRxGE bit of the TxGCON register. The
polarity of the Timer1/3/5 Gate Enable mode is
configured using the TxGPOL bit of the TxGCON
register.
When Timer1/3/5 Gate Enable mode is enabled,
Timer1/3/5 will increment on the rising edge of the
Timer1/3/5 clock source. When Timer1/3/5 Gate
Enable mode is disabled, no incrementing will occur
and Timer1/3/5 will hold the current count. See
Figure 12-4
TABLE 12-3:
DS41412D-page 164
TxCLK




Timer1/3/5 Gate
TMR1L
TxGPOL
TIMER1/3/5 GATE ENABLE
for timing details.
0
0
1
1
8
TIMER1/3/5 GATE ENABLE
SELECTIONS
8
TIMER1/3/5 16-BIT
READ/WRITE MODE
BLOCK DIAGRAM
High Byte
TMR1H
TMR1
8
TxG
0
1
0
1
8
8
Counts
Holds Count
Holds Count
Counts
Internal Data Bus
Read TMR1L
Write TMR1L
Timer1/3/5
Operation
on Overflow
Timer1/3/5
Circuitry
TMR1IF
From
Set
Preliminary
12.7.2
The Timer1/3/5 Gate source can be selected from one
of four different sources. Source selection is controlled
by the TxGSS bits of the TxGCON register. The polarity
for each available source is also selectable. Polarity
selection is controlled by the TxGPOL bit of the
TxGCON register.
TABLE 12-4:
The Gate resource, Timer2 Match to PR2, changes
between Timer2, Timer4 and Timer6 depending on
which of the three 16-bit Timers, Timer1, Timer3 or
Timer5, is selected. See
Timer2/4/6 Match to PR2/4/6 combination is available
for the 16-bit timer being used.
TABLE 12-5:
12.7.2.1
The TxG pin is one source for Timer1/3/5 Gate Control.
It can be used to supply an external source to the
Timer1/3/5 Gate circuitry.
12.7.2.2
The TMR2/4/6 register will increment until it matches
the value in the PR2/4/6 register. On the very next
increment cycle, TMR2/4/6 will be reset to 00h. When
this Reset occurs, a low-to-high pulse will automatically
be generated and internally supplied to the Timer1/3/5
Gate circuitry. See
Source Selection”
Timer1
Timer3
Timer5
TxGSS
Timer1/3/5 Resource
00
01
10
11
Timer1/3/5 Gate Pin
Timer2/4/6 Match to PR2/4/6
(TMR2/4/6 increments to match PR2/4/6)
Comparator 1 Output SYNCC1OUT
(optionally Timer1/3/5 synchronized out-
put)
Comparator 2 Output SYNCC2OUT
(optionally Timer1/3/5 synchronized out-
put)
TIMER1/3/5 GATE SOURCE
SELECTION
TxG Pin Gate Operation
Timer2/4/6 Match Gate Operation
TIMER1/3/5 GATE SOURCES
GATE RESOURCES FOR
TIMER2/4/6 MATCH TO
PR2/4/6
Timer1/3/5 Gate Source
Section 12.7.2 “Timer1/3/5 Gate
for more information.
 2010 Microchip Technology Inc.
Table 12-5
TMR2 Match to PR2
TMR4 Match to PR4
TMR6 Match to PR6
Timer1/3/5 Gate Match
Selection
to determine which