PIC18LF25K22-I/SP Microchip Technology, PIC18LF25K22-I/SP Datasheet - Page 329

• Manufacturer Part Number: PIC18LF25K22-I/SP
• Description: MCU 8BIT 32KB FLASH 3.6V 28SDIP
• Manufacturer: Microchip Technology
• Series: PIC® XLP™ 18Fr

Specifications of PIC18LF25K22-I/SP

• Program Memory Type: FLASH
• Program Memory Size: 32KB (16K x 16)
• Package / Case: 28-DIP (0.300", 7.62mm)
• Core Processor: PIC
• Core Size: 8-Bit
• Speed: 64MHz
• Connectivity: I²C, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, HLVD, POR, PWM, WDT
• Number Of I /o: 24
• Eeprom Size: 256 x 8
• Ram Size: 1.5K x 8
• Voltage - Supply (vcc/vdd): 1.8 V ~ 3.6 V
• Data Converters: A/D 19x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Processor Series: PIC18LF
• Core: PIC
• Data Bus Width: 8 bit
• Data Ram Size: 1536 B
• Interface Type: I2C, SPI, EUSART
• Maximum Clock Frequency: 64 MHz
• Number Of Programmable I/os: 25
• Number Of Timers: 7
• Operating Supply Voltage: 1.8 V to 3.6 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: Through Hole
• 3rd Party Development Tools: 52715-96, 52716-328, 52717-734, 52712-325, EWPIC18
• Development Tools By Supplier: PG164130, DV164005
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10 bit, 17 Channel
• On-chip Dac: 5 bit
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Lead free / RoHS Compliant

19.9
Upon Reset, all registers of the CTMU are cleared. This
leaves the CTMU module disabled, its current source is
turned off and all configuration options return to their
default settings. The module needs to be re-initialized
following any Reset.
If the CTMU is in the process of taking a measurement at
the time of Reset, the measurement will be lost. A partial
charge may exist on the circuit that was being measured,
and should be properly discharged before the CTMU
makes subsequent attempts to make a measurement.
The circuit is discharged by setting and then clearing the
IDISSEN bit (CTMUCONH<1>) while the A/D Converter
is connected to the appropriate channel.
REGISTER 19-1:
 2010 Microchip Technology Inc.
bit 7
Legend:
R = Readable bit
-n = Value at POR
bit 7
bit 6
bit 5
bit 4
bit 3
bit 2
bit 1
bit 0
CTMUEN
R/W-0
Effects of a Reset on CTMU
CTMUEN: CTMU Enable bit
1 = Module is enabled
0 = Module is disabled
Unimplemented: Read as ‘0’
CTMUSIDL: Stop in Idle Mode bit
1 = Discontinue module operation when device enters Idle mode
0 = Continue module operation in Idle mode
TGEN: Time Generation Enable bit
1 = Enables edge delay generation
0 = Disables edge delay generation
EDGEN: Edge Enable bit
1 = Edges are not blocked
0 = Edges are blocked
EDGSEQEN: Edge Sequence Enable bit
1 = Edge 1 event must occur before Edge 2 event can occur
0 = No edge sequence is needed
IDISSEN: Analog Current Source Control bit
1 = Analog current source output is grounded
0 = Analog current source output is not grounded
CTTRIG: CTMU Special Event Trigger Control Bit
1 = CTMU Special Event Trigger is enabled
0 = CTMU Special Event Trigger is disabled
U-0
—
CTMUCONH: CTMU CONTROL REGISTER 0
W = Writable bit
‘1’ = Bit is set
CTMUSIDL
R/W-0
R/W-0
TGEN
Preliminary
U = Unimplemented bit, read as ‘0’
‘0’ = Bit is cleared
EDGEN
R/W-0
19.10 Registers
There are three control registers for the CTMU:
• CTMUCONH
• CTMUCONL
• CTMUICON
The
(Register 19-1
for configuring the CTMU module edge source selec-
tion, edge source polarity selection, edge sequencing,
A/D trigger, analog circuit capacitor discharge and
enables. The CTMUICON register
bits for selecting the current source range and current
source trim.
PIC18(L)F2X/4XK22
CTMUCONH
EDGSEQEN
R/W-0
and
Register
and
x = Bit is unknown
IDISSEN
19-2) contain control bits
R/W-0
CTMUCONL
(Register
DS41412D-page 329
CTTRIG
19-3) has
U-0
registers
bit 0