PIC18LF25K22-I/SP Microchip Technology, PIC18LF25K22-I/SP Datasheet - Page 257

• Manufacturer Part Number: PIC18LF25K22-I/SP
• Description: MCU 8BIT 32KB FLASH 3.6V 28SDIP
• Manufacturer: Microchip Technology
• Series: PIC® XLP™ 18Fr

Specifications of PIC18LF25K22-I/SP

• Program Memory Type: FLASH
• Program Memory Size: 32KB (16K x 16)
• Package / Case: 28-DIP (0.300", 7.62mm)
• Core Processor: PIC
• Core Size: 8-Bit
• Speed: 64MHz
• Connectivity: I²C, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, HLVD, POR, PWM, WDT
• Number Of I /o: 24
• Eeprom Size: 256 x 8
• Ram Size: 1.5K x 8
• Voltage - Supply (vcc/vdd): 1.8 V ~ 3.6 V
• Data Converters: A/D 19x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Processor Series: PIC18LF
• Core: PIC
• Data Bus Width: 8 bit
• Data Ram Size: 1536 B
• Interface Type: I2C, SPI, EUSART
• Maximum Clock Frequency: 64 MHz
• Number Of Programmable I/os: 25
• Number Of Timers: 7
• Operating Supply Voltage: 1.8 V to 3.6 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: Through Hole
• 3rd Party Development Tools: 52715-96, 52716-328, 52717-734, 52712-325, EWPIC18
• Development Tools By Supplier: PG164130, DV164005
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10 bit, 17 Channel
• On-chip Dac: 5 bit
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Lead free / RoHS Compliant

REGISTER 15-2:
 2010 Microchip Technology Inc.
bit 3-0
Note 1:
2:
3:
4:
In Master mode, the overflow bit is not set since each new reception (and transmission) is initiated by writing to the
SSPxBUF register.
When enabled, these pins must be properly configured as input or output.
When enabled, the SDAx and SCLx pins must be configured as inputs.
SSPxADD values of 0, 1 or 2 are not supported for I
SSPxM<3:0>: Synchronous Serial Port Mode Select bits
0000 = SPI Master mode, clock = F
0001 = SPI Master mode, clock = F
0010 = SPI Master mode, clock = F
0011 = SPI Master mode, clock = TMR2 output/2
0100 = SPI Slave mode, clock = SCKx pin, SSx pin control enabled
0101 = SPI Slave mode, clock = SCKx pin, SSx pin control disabled, SSx can be used as I/O pin
0110 = I
0111 = I
1000 = I
1001 = Reserved
1010 = SPI Master mode, clock = F
1011 = I
1100 = Reserved
1101 = Reserved
1110 = I
1111 = I
SSPxCON1: SSPx CONTROL REGISTER 1 (CONTINUED)
2
2
2
2
2
2
C Slave mode, 7-bit address
C Slave mode, 10-bit address
C Master mode, clock = F
C firmware controlled Master mode (slave idle)
C Slave mode, 7-bit address with Start and Stop bit interrupts enabled
C Slave mode, 10-bit address with Start and Stop bit interrupts enabled
OSC
OSC
OSC
OSC
OSC
Preliminary
/4
/16
/64
/(4 * (SSPxADD+1))
/ (4 * (SSPxADD+1))
2
C Mode.
PIC18(L)F2X/4XK22
(4)
DS41412D-page 257