ATMEGA8A-PU Atmel, ATMEGA8A-PU Datasheet - Page 100

• Manufacturer Part Number: ATMEGA8A-PU
• Description: MCU AVR 8K FLASH 16MHZ 28-PDIP
• Manufacturer: Atmel
• Series: AVR® ATmegar

Specifications of ATMEGA8A-PU

• Core Processor: AVR
• Core Size: 8-Bit
• Speed: 16MHz
• Connectivity: I²C, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 23
• Program Memory Size: 8KB (4K x 16)
• Program Memory Type: FLASH
• Eeprom Size: 512 x 8
• Ram Size: 1K x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 5.5 V
• Data Converters: A/D 6x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 28-DIP (0.300", 7.62mm)
• Processor Series: ATMEGA8x
• Core: AVR8
• Data Bus Width: 8 bit
• Data Ram Size: 1 KB
• Interface Type: SPI, TWI, USART
• Maximum Clock Frequency: 16 MHz
• Number Of Programmable I/os: 23
• Number Of Timers: 3
• Maximum Operating Temperature: + 85 C
• Mounting Style: Through Hole
• 3rd Party Development Tools: EWAVR, EWAVR-BL
• Development Tools By Supplier: ATAVRDRAGON, ATSTK500, ATSTK600, ATAVRISP2, ATAVRONEKIT
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10 bit, 6 Channel
• Package: 28PDIP
• Device Core: AVR
• Family Name: ATmega
• Maximum Speed: 16 MHz
• Operating Supply Voltage: 3.3|5 V
• Controller Family/series: AVR MEGA
• No. Of I/o's: 23
• Eeprom Memory Size: 512Byte
• Ram Memory Size: 1KB
• Cpu Speed: 16MHz
• Rohs Compliant: Yes
• For Use With: ATSTK600 - DEV KIT FOR AVR/AVR32ATSTK500 - PROGRAMMER AVR STARTER KIT
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

8159D–AVR–02/11
Table 16-3
PWM mode.
Table 16-3.
Note:
Table 16-4
correct or the phase and frequency correct, PWM mode.
Table 16-4.
Note:
• Bit 3 – FOC1A: Force Output Compare for channel A
• Bit 2 – FOC1B: Force Output Compare for channel B
The FOC1A/FOC1B bits are only active when the WGM13:0 bits specifies a non-PWM mode.
However, for ensuring compatibility with future devices, these bits must be set to zero when
TCCR1A is written when operating in a PWM mode. When writing a logical one to the
FOC1A/FOC1B bit, an immediate Compare Match is forced on the waveform generation unit.
The OC1A/OC1B output is changed according to its COM1x1:0 bits setting. Note that the
FOC1A/FOC1B bits are implemented as strobes. Therefore it is the value present in the
COM1x1:0 bits that determine the effect of the forced compare.
A FOC1A/FOC1B strobe will not generate any interrupt nor will it clear the timer in Clear Timer
on Compare Match (CTC) mode using OCR1A as TOP.
COM1A1/
COM1A1/
COM1B1
COM1B1
0
0
1
1
0
0
1
1
1. A special case occurs when OCR1A/OCR1B equals TOP and COM1A1/COM1B1 is set. In
1. A special case occurs when OCR1A/OCR1B equals TOP and COM1A1/COM1B1 is set.
this case the Compare Match is ignored, but the set or clear is done at BOTTOM.
PWM Mode” on page 91.
“Phase Correct PWM Mode” on page 93.
shows the COM1x1:0 bit functionality when the WGM13:0 bits are set to the phase
shows the COM1x1:0 bit functionality when the WGM13:0 bits are set to the fast
Compare Output Mode, Fast PWM
Compare Output Mode, Phase Correct and Phase and Frequency Correct
PWM
COM1A0/
COM1A0/
COM1B0
COM1B0
(1)
0
1
0
1
0
1
0
1
Description
Normal port operation, OC1A/OC1B disconnected.
WGM13:0 = 9 or 14: Toggle OC1A on Compare Match, OC1B
disconnected (normal port operation). For all other WGM1 settings,
normal port operation, OC1A/OC1B disconnected.
Clear OC1A/OC1B on Compare Match when up-counting. Set
OC1A/OC1B on Compare Match when downcounting.
Set OC1A/OC1B on Compare Match when up-counting. Clear
OC1A/OC1B on Compare Match when downcounting.
Description
Normal port operation, OC1A/OC1B disconnected.
WGM13:0 = 15: Toggle OC1A on Compare Match, OC1B disconnected
(normal port operation). For all other WGM1 settings, normal port
operation, OC1A/OC1B disconnected.
Clear OC1A/OC1B on Compare Match, set OC1A/OC1B at BOTTOM,
(non-inverting mode)
Set OC1A/OC1B on Compare Match, clear OC1A/OC1B at BOTTOM,
(inverting mode)
for more details.
for more details.
(1)
ATmega8A
See “Fast
See
100