UPD78F0513AGB-GAF-AX Renesas Electronics America, UPD78F0513AGB-GAF-AX Datasheet - Page 284

• Manufacturer Part Number: UPD78F0513AGB-GAF-AX
• Description: MCU 8BIT 44-LQFP
• Manufacturer: Renesas Electronics America
• Series: 78K0/Kx2r

Specifications of UPD78F0513AGB-GAF-AX

• Core Processor: 78K/0
• Core Size: 8-Bit
• Speed: 20MHz
• Connectivity: 3-Wire SIO, I²C, LIN, UART/USART
• Peripherals: LVD, POR, PWM, WDT
• Number Of I /o: 37
• Program Memory Size: 32KB (32K x 8)
• Program Memory Type: FLASH
• Ram Size: 1K x 8
• Voltage - Supply (vcc/vdd): 1.8 V ~ 5.5 V
• Data Converters: A/D 8x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: *
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -

78K0/Kx2
R01UH0008EJ0401 Rev.4.01
Jul 15, 2010
Address: FFB9H
Symbol
TOC01
The value of this bit is always 0 when it is read. Do not set this bit to 1 in a mode other than the one-shot
pulse output mode.
If it is set to 1, TM01 is cleared and started.
One-shot pulse output operates correctly in the free-running timer mode or clear & start mode entered by
TI001 pin valid edge input.
The one-shot pulse cannot be output in the clear & start mode entered upon a match between TM01 and
CR001.
The interrupt signal (INTTM011) is generated even when TOC014 = 0.
• LVS01 and LVR01 can be used to set the initial value of the TO01 output level. If the initial value does
• Be sure to set LVS01 and LVR01 when TOE01 = 1.
• LVS01 and LVR01 are trigger bits. By setting these bits to 1, the initial value of the TO01 output level
• The values of LVS01 and LVR01 are always 0 when they are read.
• For how to set LVS01 and LVR01, see 7.5.2 Setting LVS0n and LVR0n.
• The actual TO01/TI011/P06 pin output is determined depending on PM06 and P06, besides TO01
The interrupt signal (INTTM001) is generated even when TOC011 = 0.
OSPE01
OSPT01
TOC014
TOC011
TOE01
LVS01
not have to be set, leave LVS01 and LVR01 as 00.
LVS01, LVR01, and TOE01 being simultaneously set to 1 is prohibited.
can be set. Even if these bits are cleared to 0, TO01 output is not affected.
output.
7
0
0
1
0
1
0
1
0
0
1
1
0
1
0
1
Figure 7-12. Format of 16-Bit Timer Output Control Register 01 (TOC01)
After reset: 00H
Disables inversion operation
Enables inversion operation
One-shot pulse output
Successive pulse output
One-shot pulse output
Disables inversion operation
Enables inversion operation
Disables output (TO01 output is fixed to low level)
Enables output
OSPT01
LVR01
<6>
0
1
0
1
R/W
No change
Initial value of TO01 output is low level (TO01 output is cleared to 0).
Initial value of TO01 output is high level (TO01 output is set to 1).
Setting prohibited
OSPE01
<5>
TO01 output control on match between CR011 and TM01
TO01 output control on match between CR001 and TM01
CHAPTER 7 16-BIT TIMER/EVENT COUNTERS 00 AND 01
One-shot pulse output trigger via software
One-shot pulse output operation control
TOC014
4
TO01 output control
Setting of TO01 output status
LVS01
<3>
−
LVR01
<2>
TOC011
1
TOE01
<0>
284