PIC16LC65-04I/L Microchip Technology, PIC16LC65-04I/L Datasheet - Page 69

• Manufacturer Part Number: PIC16LC65-04I/L
• Description: IC MIC CTL 4K LP OTP IT 44PLCC
• Manufacturer: Microchip Technology
• Series: PIC® 16Cr

Specifications of PIC16LC65-04I/L

• Core Processor: PIC
• Core Size: 8-Bit
• Speed: 4MHz
• Connectivity: I²C, SPI, UART/USART
• Peripherals: POR, PWM, WDT
• Number Of I /o: 33
• Program Memory Size: 7KB (4K x 14)
• Program Memory Type: OTP
• Ram Size: 192 x 8
• Voltage - Supply (vcc/vdd): 3 V ~ 6 V
• Oscillator Type: External
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 44-PLCC
• Lead Free Status / RoHS Status: Request inventory verification / Request inventory verification
• Eeprom Size: -
• Data Converters: -

7.3.1
The prescaler assignment is fully under software con-
trol, i.e., it can be changed “on the fly” during program
execution.
EXAMPLE 7-1:
To change prescaler from the WDT to the Timer0 mod-
ule, use the sequence shown in Example 7-2.
EXAMPLE 7-2:
TABLE 7-1:
Lines 2 and 3 do NOT have to
be included if the final desired
prescale value is other than 1:1.
If 1:1 is final desired value, then
a temporary prescale value is
set in lines 2 and 3 and the final
prescale value will be set in lines
10 and 11.
Address
01h, 101h
0Bh,8Bh,
10Bh,18Bh
81h, 181h
85h
Legend: x = unknown, u = unchanged, - = unimplemented locations read as '0'. Shaded cells are not used by Timer0.
Note 1: TRISA<5> and bit PEIE are not implemented on the PIC16C61, read as '0'.
1997 Microchip Technology Inc.
Note:
CLRWDT
BSF
MOVLW
MOVWF
BCF
SWITCHING PRESCALER ASSIGNMENT
To avoid an unintended device RESET, the
following instruction sequence (shown in
Example 7-1) must be executed when
changing the prescaler assignment from
Timer0 to the WDT. This precaution must
be followed even if the WDT is disabled.
Name
TMR0
INTCON
OPTION RBPU INTEDG
TRISA
STATUS, RP0 ;Bank 1
b'xxxx0xxx' ;Select TMR0, new prescale value and clock source
OPTION_REG
STATUS, RP0 ;Bank 0
REGISTERS ASSOCIATED WITH TIMER0
CHANGING PRESCALER (TIMER0 WDT)
CHANGING PRESCALER (WDT TIMER0)
Timer0 module’s register
Bit 7
GIE
—
;Clear WDT and prescaler
;
PEIE
Bit 6
—
(1)
1)
2)
3)
4)
5)
6)
7)
8)
9)
10) MOVLW
11) MOVWF
12) BCF
PORTA Data Direction Register
BSF
MOVLW
MOVWF
BCF
CLRF
BSF
MOVLW
MOVWF
CLRWDT
T0CS
Bit 5
T0IE
STATUS, RP0
b'xx0x0xxx'
OPTION_REG
STATUS, RP0
TMR0
STATUS, RP1
b'xxxx1xxx'
OPTION_REG
b'xxxx1xxx'
OPTION_REG
STATUS, RP0
T0SE
Bit 4
INTE
RBIE
Bit 3
PSA
(1)
;Bank 1
;Select clock source and prescale value of
;other than 1:1
;Bank 0
;Clear TMR0 and prescaler
;Bank 1
;Select WDT, do not change prescale value
;
;Clears WDT and prescaler
;Select new prescale value and WDT
;
;Bank 0
Bit 2
T0IF
PS2
Bit 1
INTF
PS1
RBIF
Bit 0
PS0
PIC16C6X
xxxx xxxx
0000 000x
1111 1111
--11 1111
Value on:
POR,
BOR
DS30234D-page 69
other resets
Value on all
uuuu uuuu
0000 000u
1111 1111
--11 1111