X8-A11-E-A Digi International, X8-A11-E-A Datasheet - Page 163
X8-A11-E-A
Manufacturer Part Number
X8-A11-E-A
Description
CONNECTPORT X8 2.4GHZ
Manufacturer
Digi International
Series
ConnectPort™ X8r
Specifications of X8-A11-E-A
Function
Transceiver, Xbee, Gateway
Modulation Or Protocol
UDP/TCP, DHCP, SNMPv1
Frequency
2.4GHz
Applications
General Purpose
Interface
RJ45, DB-9, 2 USB
Sensitivity
-93dBm
Power - Output
15dBm
Data Rate - Maximum
54Mbps
Voltage - Supply
12VDC
Wireless Frequency
2.4 GHz
Interface Type
RS-232, Ethernet, USB
Modulation
BPSK, CCK, DBPSK, DQPSK, QPSK
Security
256 bit AES, 3DES, DES, SSL Tunnel
Operating Voltage
9 V to 30 V
Output Power
3.1 W
Antenna
4 in Dipole with 2 ft Cable
Operating Temperature Range
- 30 C to + 60 C
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Features
-
Lead Free Status / Rohs Status
Lead free / RoHS Compliant
Other names
602-1171
- Current page: 163 of 254
- Download datasheet (3Mb)
Advanced remote management settings
The default settings for remote management usually work for most situations. These Advanced
settings are used in advanced situations. They are used to configure the idle timeout for the
connection between the Digi device and the remote management server, and the keep-alive settings
of the various interfaces (TCP and HTTP for mobile and Ethernet network connections). These
settings should only be changed when the defaults do not properly work.
Connection Settings: These settings configure the idle timeout for the connection
between the Digi device and the remote management server.
–
–
Mobile Settings:
Ethernet Settings
WiFi Settings: These settings apply to client-initiated management connections over
mobile/cellular, Ethernet, and Wi-Fi networks.
–
–
remote management server before assuming the connection is lost.
messages.
application can tolerate to reduce the amount of data traffic.
Digi device assumes the connection to the remote management server is lost and
drops the connection.
good enough for most connections. It is the most efficient method of connecting to
the remote server in terms of speed and transmitted data bytes.
is less efficient than TCP, but it is useful in situations where a firewall or proxy may
prevent direct connection via TCP. Automatic will try each combination until a
connection is made. This connection method requires the HTTP over Proxy Settings
to be specified.
Disconnect when Connectware Management is idle: Enables or disables the idle
timeout for the connection. If enabled, the connection will be dropped, or ended, after
the amount of time specified in the Idle Timeout setting.
Idle Timeout: The amount of time to wait before timing out the connection.
Connectware Management Protocol Keep-Alive Settings: These settings control how
often keep-alive packets are sent over the client-initiated connection to the remote
management server, and whether the device waits before dropping the connection.
Receive Interval: The number of seconds to wait for a keep-alive message from the
Transmit Interval: The number of seconds to wait between sending keep-alive
Important: It is recommended that this interval value be set as long as your
Assume connection is lost after n timeouts: How many timeouts occur before the
Connection Method: The method for connecting to the remote management server.
TCP: Connect using TCP. This is the default connection method, and is typically
Automatic: Automatically detect the connection method. This connection method
None: This value has the same effect as selecting TCP.
HTTP: Connect using HTTP.
HTTP over Proxy: Connect using HTTP.
C o n f i g u r e D i g i d e v i c e s
1 6 3
Related parts for X8-A11-E-A
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
Zigbee / 802.15.4 Modules & Development Tools Connect port IP/Xbee RF/DiN Products
Manufacturer:
Digi International
Datasheet:
Part Number:
Description:
Zigbee / 802.15.4 Modules & Development Tools Connect port IP/Xbee RF/DiN Products
Manufacturer:
Digi International
Datasheet:
Part Number:
Description:
Zigbee / 802.15.4 Modules & Development Tools Connect port IP/Xbee RF/DiN Products
Manufacturer:
Digi International
Datasheet:
Part Number:
Description:
Zigbee / 802.15.4 Modules & Development Tools Connect port IP/Xbee RF/DiN Products
Manufacturer:
Digi International
Datasheet:
Part Number:
Description:
KIT JUMP START ME 9210 NET+OS 7
Manufacturer:
Digi International
Datasheet:
Part Number:
Description:
KIT JUMP START ME 9210 LINUX
Manufacturer:
Digi International
Datasheet:
Part Number:
Description:
KIT INTEGRATION ME MOD S MODELS
Manufacturer:
Digi International
Datasheet:
Part Number:
Description:
KIT DEV SP ADPT NO RAVEN
Manufacturer:
Digi International
Datasheet:
Part Number:
Description:
KIT DEV SP ADAPTER
Manufacturer:
Digi International
Datasheet:
Part Number:
Description:
DIGI CONNECT 4MB FLASH 8MB RAM
Manufacturer:
Digi International
Datasheet:
Part Number:
Description:
IC ARM MICROPROCESSOR 177BGA
Manufacturer:
Digi International
Datasheet:
Part Number:
Description:
DIGI CONNECT 4MB FLASH 8MB RAM
Manufacturer:
Digi International
Datasheet:
Part Number:
Description:
ME 8MB SDRAM 2MB FLASH SINGLE
Manufacturer:
Digi International
Datasheet:
Part Number:
Description:
ME 8MB SDRAM 2MB FLASH SINGLE
Manufacturer:
Digi International
Datasheet:
Part Number:
Description:
MODULE 9P 8MB SDRAM 4MB FLASH
Manufacturer:
Digi International/Maxstream
Datasheet: