SI1015-A-GM Silicon Laboratories Inc, SI1015-A-GM Datasheet - Page 27

• Manufacturer Part Number: SI1015-A-GM
• Description: IC TXRX MCU + EZRADIOPRO
• Manufacturer: Silicon Laboratories Inc

Specifications of SI1015-A-GM

• Package / Case: 42-QFN
• Frequency: 240MHz ~ 960MHz
• Data Rate - Maximum: 256kbps
• Modulation Or Protocol: FSK, GFSK, OOK
• Applications: General Purpose
• Power - Output: 13dBm
• Sensitivity: -121dBm
• Voltage - Supply: 0.9 V ~ 3.6 V
• Current - Receiving: 18.5mA
• Current - Transmitting: 30mA
• Data Interface: PCB, Surface Mount
• Memory Size: 8kB Flash, 768B RAM
• Antenna Connector: PCB, Surface Mount
• Number Of Receivers: 1
• Number Of Transmitters: 1
• Wireless Frequency: 240 MHz to 960 MHz
• Interface Type: UART, SMBus, SPI, PCA
• Output Power: 13 dBm
• Operating Supply Voltage: 0.9 V to 3.6 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• Maximum Supply Current: 4 mA
• Minimum Operating Temperature: - 40 C
• Modulation: FSK, GFSK, OOK
• Protocol Supported: C2, SMBus
• Core: 8051
• Program Memory Type: Flash
• Program Memory Size: 8 KB
• Data Ram Size: 768 B
• Supply Current (max): 4 mA
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Operating Temperature: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: 336-1868-5

1.4. Serial Ports
The Si1010/1/2/3/4/5 Family includes an SMBus/I
rate configuration, and two Enhanced SPI interfaces. Each of the serial buses is fully implemented in hard-
ware and makes extensive use of the CIP-51's interrupts, thus requiring very little CPU intervention.
1.5. Programmable Counter Array
An on-chip Programmable Counter/Timer Array (PCA) is included in addition to the four 16-bit general pur-
pose counter/timers. The PCA consists of a dedicated 16-bit counter/timer time base with six programma-
ble capture/compare modules. The PCA clock is derived from one of six sources: the system clock divided
by 12, the system clock divided by 4, Timer 0 overflows, an External Clock Input (ECI), the system clock, or
the external oscillator clock source divided by 8. ‘F912 and ‘F902 devices also support a SmaRTClock
divided by 8 clock source.
Each capture/compare module can be configured to operate in a variety of modes: edge-triggered capture,
software timer, high-speed output, pulse width modulator (8, 9, 10, 11, or 16-bit), or frequency output. Addi-
tionally, Capture/Compare Module 5 offers watchdog timer (WDT) capabilities. Following a system reset,
Module 5 is configured and enabled in WDT mode. The PCA Capture/Compare Module I/O and External
Clock Input may be routed to Port I/O via the Digital Crossbar.
Capture/Compare
Module 0
SYSCLK/12
Timer 0 Overflow
SYSCLK
External Clock/8
SmaRTClock/8
SYSCLK/4
ECI
Capture/Compare
Module 1
CLOCK
MUX
PCA
Figure 1.10. PCA Block Diagram
16-Bit Counter/Timer
Port I/O
Capture/Compare
Module 2
Crossbar
Rev. 1.0
2
C interface, a full-duplex UART with enhanced baud
Capture/Compare
Module 3
Si1010/1/2/3/4/5
Capture/Compare
Module 4
Capture/Compare
Module 5 / WDT
27