SI1015-A-GM Silicon Laboratories Inc, SI1015-A-GM Datasheet - Page 333

• Manufacturer Part Number: SI1015-A-GM
• Description: IC TXRX MCU + EZRADIOPRO
• Manufacturer: Silicon Laboratories Inc

Specifications of SI1015-A-GM

• Package / Case: 42-QFN
• Frequency: 240MHz ~ 960MHz
• Data Rate - Maximum: 256kbps
• Modulation Or Protocol: FSK, GFSK, OOK
• Applications: General Purpose
• Power - Output: 13dBm
• Sensitivity: -121dBm
• Voltage - Supply: 0.9 V ~ 3.6 V
• Current - Receiving: 18.5mA
• Current - Transmitting: 30mA
• Data Interface: PCB, Surface Mount
• Memory Size: 8kB Flash, 768B RAM
• Antenna Connector: PCB, Surface Mount
• Number Of Receivers: 1
• Number Of Transmitters: 1
• Wireless Frequency: 240 MHz to 960 MHz
• Interface Type: UART, SMBus, SPI, PCA
• Output Power: 13 dBm
• Operating Supply Voltage: 0.9 V to 3.6 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• Maximum Supply Current: 4 mA
• Minimum Operating Temperature: - 40 C
• Modulation: FSK, GFSK, OOK
• Protocol Supported: C2, SMBus
• Core: 8051
• Program Memory Type: Flash
• Program Memory Size: 8 KB
• Data Ram Size: 768 B
• Supply Current (max): 4 mA
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Operating Temperature: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: 336-1868-5

SFR Definition 26.8. SPI0CN: SPI0 Control
SFR Page = 0x0; SFR Address = 0xF8; Bit-Addressable
Name
Reset
Bit
3:2
Type
7
6
5
4
1
0
Bit
NSSMD[1:0]
RXOVRN
TXBMT
WCOL
SPIEN
MODF
Name
SPIF
SPIF
R/W
7
0
SPI0 Interrupt Flag.
This bit is set to logic 1 by hardware at the end of a data transfer. If SPI interrupts
are enabled, an interrupt will be generated. This bit is not automatically cleared by
hardware, and must be cleared by software.
Write Collision Flag.
This bit is set to logic 1 if a write to SPI0DAT is attempted when TXBMT is 0. When
this occurs, the write to SPI0DAT will be ignored, and the transmit buffer will not be
written. If SPI interrupts are enabled, an interrupt will be generated. This bit is not
automatically cleared by hardware, and must be cleared by software.
Mode Fault Flag.
This bit is set to logic 1 by hardware when a master mode collision is detected
(NSS is low, MSTEN = 1, and NSSMD[1:0] = 01). If SPI interrupts are enabled, an
interrupt will be generated. This bit is not automatically cleared by hardware, and
must be cleared by software.
Receive Overrun Flag (valid in slave mode only).
This bit is set to logic 1 by hardware when the receive buffer still holds unread data
from a previous transfer and the last bit of the current transfer is shifted into the
SPI0 shift register. If SPI interrupts are enabled, an interrupt will be generated. This
bit is not automatically cleared by hardware, and must be cleared by software.
Slave Select Mode.
Selects between the following NSS operation modes:
(See Section 26.2 and Section 26.3).
00: 3-Wire Slave or 3-Wire Master Mode. NSS signal is not routed to a port pin.
01: 4-Wire Slave or Multi-Master Mode (Default). NSS is an input to the device.
1x: 4-Wire Single-Master Mode. NSS signal is mapped as an output from the
device and will assume the value of NSSMD0.
Transmit Buffer Empty.
This bit will be set to logic 0 when new data has been written to the transmit buffer.
When data in the transmit buffer is transferred to the SPI shift register, this bit will
be set to logic 1, indicating that it is safe to write a new byte to the transmit buffer.
SPI0 Enable.
0: SPI disabled.
1: SPI enabled.
WCOL
R/W
6
0
MODF
R/W
5
0
RXOVRN
R/W
Rev. 1.0
4
0
Function
3
0
NSSMD[1:0]
R/W
Si1010/1/2/3/4/5
2
1
TXBMT
R
1
1
SPIEN
R/W
0
0
333