SI1015-A-GM Silicon Laboratories Inc, SI1015-A-GM Datasheet - Page 369

• Manufacturer Part Number: SI1015-A-GM
• Description: IC TXRX MCU + EZRADIOPRO
• Manufacturer: Silicon Laboratories Inc

Specifications of SI1015-A-GM

• Package / Case: 42-QFN
• Frequency: 240MHz ~ 960MHz
• Data Rate - Maximum: 256kbps
• Modulation Or Protocol: FSK, GFSK, OOK
• Applications: General Purpose
• Power - Output: 13dBm
• Sensitivity: -121dBm
• Voltage - Supply: 0.9 V ~ 3.6 V
• Current - Receiving: 18.5mA
• Current - Transmitting: 30mA
• Data Interface: PCB, Surface Mount
• Memory Size: 8kB Flash, 768B RAM
• Antenna Connector: PCB, Surface Mount
• Number Of Receivers: 1
• Number Of Transmitters: 1
• Wireless Frequency: 240 MHz to 960 MHz
• Interface Type: UART, SMBus, SPI, PCA
• Output Power: 13 dBm
• Operating Supply Voltage: 0.9 V to 3.6 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• Maximum Supply Current: 4 mA
• Minimum Operating Temperature: - 40 C
• Modulation: FSK, GFSK, OOK
• Protocol Supported: C2, SMBus
• Core: 8051
• Program Memory Type: Flash
• Program Memory Size: 8 KB
• Data Ram Size: 768 B
• Supply Current (max): 4 mA
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Operating Temperature: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: 336-1868-5

28.3.6. 16-Bit Pulse Width Modulator Mode
A PCA module may also be operated in 16-Bit PWM mode. 16-bit PWM mode is independent of the other
(8/9/10/11-bit) PWM modes. In this mode, the 16-bit capture/compare module defines the number of PCA
clocks for the low time of the PWM signal. When the PCA counter matches the module contents, the
output on CEXn is asserted high; when the 16-bit counter overflows, CEXn is asserted low. To output a
varying duty cycle, new value writes should be synchronized with PCA CCFn match interrupts. 16-Bit
PWM Mode is enabled by setting the ECOMn, PWMn, and PWM16n bits in the PCA0CPMn register. For a
varying duty cycle, match interrupts should be enabled (ECCFn = 1 AND MATn = 1) to help synchronize
the capture/compare register writes. If the MATn bit is set to 1, the CCFn flag for the module will be set
each time a 16-bit comparator match (rising edge) occurs. The CF flag in PCA0CN can be used to detect
the overflow (falling edge). The duty cycle for 16-Bit PWM Mode is given by Equation 28.4.
Important Note About Capture/Compare Registers : When writing a 16-bit value to the PCA0
Capture/Compare registers, the low byte should always be written first. Writing to PCA0CPLn clears the
ECOMn bit to 0; writing to PCA0CPHn sets ECOMn to 1.
Using Equation 28.4, the largest duty cycle is 100% (PCA0CPn = 0), and the smallest duty cycle is
0.0015% (PCA0CPn = 0xFFFF). A 0% duty cycle may be generated by clearing the ECOMn bit to 0.
PCA0CPLn
Write to
Reset
PCA0CPHn
Write to
0
ENB
ENB
1
Figure 28.9. PCA 9, 10 and 11-Bit PWM Mode Diagram
W
M
P
0
1
6
n
E
C
O
M
n
PCA0CPMn
C
A
P
P
n
0 0 x 0
C
A
P
N
n
M
A
T
n
O
G
T
n
Equation 28.4. 16-Bit PWM Duty Cycle
W
M
P
n
Duty Cycle
E
C
C
F
n
x
PCA Timebase
ARSEL = 1
ARSEL = 0
R/W when
R/W when
Enable
=
N-bit Comparator
(Capture/Compare)
PCA0CPH:Ln
PCA0CPH:Ln
(Auto-Reload)
(right-justified)
(right-justified)
Rev. 1.0

---------------------------------------------------- -
PCA0H:L
65536 PCA0CPn
–
65536
Overflow of N
match
th
R
A
S
E
L
Bit
O
S
R
PCA0PWM
E
C
V
x

C
O
V
F
Si1010/1/2/3/4/5
CLR
SET
Q
Q
C
S
E
L
L
1
CEXn
C
L
S
E
L
0
Set “N” bits:
01 = 9 bits
10 = 10 bits
11 = 11 bits
Crossbar
Port I/O
369