MA160014 Microchip Technology, MA160014 Datasheet - Page 34

• Manufacturer Part Number: MA160014
• Description: MOD PLUG-IN 44PIN PIC18LF45K22
• Manufacturer: Microchip Technology
• Series: PIC® XLP™ 18Fr

Specifications of MA160014

• Accessory Type: Plug-In Module (PIM) - PIC18LF45K10
• Product: Microcontroller Modules
• Data Bus Width: 8 bit
• Core Processor: PIC18LF45K22
• Interface Type: I2C, SPI
• Operating Supply Voltage: 1.8 V to 5.5 V
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With/related Products: PICDEM PIC18 Explorer, DM183032
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

PIC18(L)F2X/4XK22
2.3
Clock Source modes can be classified as external or
internal.
• External Clock modes rely on external circuitry for
• Internal clock sources are contained internally
The system clock can be selected between external or
internal clock sources via the System Clock Select
(SCS<1:0>) bits of the OSCCON register. See
Section 2.9
information.
TABLE 2-2:
2.4.2
The External Clock (EC) mode allows an externally
generated logic level as the system clock source. When
operating in this mode, an external clock source is
connected to the OSC1 input and the OSC2 is available
for general purpose I/O.
connections for EC mode.
The External Clock (EC) mode offers a Medium Power
(MP) and a High Power (HP) option selectable by the
FOSC<3:0> bits. The MP selections are best suited for
external clock frequencies between 4 and 16 MHz. The
HP selection is best suited for clock frequencies above
16 MHz.
The Oscillator Start-up Timer (OST) is disabled when
EC mode is selected. Therefore, there is no delay in
operation after a Power-on Reset (POR) or wake-up
from Sleep. Because the PIC
static, stopping the external clock input will have the
effect of halting the device while leaving all data intact.
Upon restarting the external clock, the device will
resume operation as if no time had elapsed.
DS41412D-page 34
Sleep/POR
Sleep/POR
LFINTOSC (31.25 kHz)
Sleep/POR
Sleep/POR
LFINTOSC (31.25 kHz)
the clock source. Examples are: Clock modules
(EC mode), quartz crystal resonators or ceramic
resonators (LP, XT and HS modes) and Resistor-
Capacitor (RC mode) circuits.
within the Oscillator block. The Oscillator block
has three internal oscillators: the 16 MHz High-
Frequency Internal Oscillator (HFINTOSC),
500 kHz Medium-Frequency Internal Oscillator
(MFINTOSC) and the 31.25 kHz Low-Frequency
Internal Oscillator (LFINTOSC).
Switch From
Clock Source Modes
EC MODE
“Clock
OSCILLATOR DELAY EXAMPLES
Switching”
Figure 2-5
®
MCU design is fully
MFINTOSC
HFINTOSC
HFINTOSC
LFINTOSC
LFINTOSC
Switch To
LP, XT, HS
EC, RC
EC, RC
4xPLL
shows the pin
for
additional
Preliminary
31.25 kHz to 500 kHz
31.25 kHz to 16 MHz
31.25 kHz to 16 MHz
32 MHz to 64 MHz
32 kHz to 40 MHz
DC – 64 MHz
DC – 64 MHz
Frequency
31.25 kHz
2.4
2.4.1
When the oscillator module is configured for LP, XT or
HS modes, the Oscillator Start-up Timer (OST) counts
1024 oscillations from OSC1. This occurs following a
Power-on Reset (POR) and when the Power-up Timer
(PWRT) has expired (if configured), or a wake-up from
Sleep. During this time, the program counter does not
increment and program execution is suspended. The
OST ensures that the oscillator circuit, using a quartz
crystal resonator or ceramic resonator, has started and
is providing a stable system clock to the oscillator
module. When switching between clock sources, a
delay is required to allow the new clock to stabilize.
These oscillator delays are shown in
In order to minimize latency between external oscillator
start-up and code execution, the Two-Speed Clock
Start-up mode can be selected (see
“Two-Speed Clock Start-up
FIGURE 2-5:
Note 1:
Clock from
Ext. System
External Clock Modes
OSCILLATOR START-UP TIMER
(OST)
Alternate pin functions are listed in
Section 1.0 “Device
Oscillator Warm-Up Delay (T
2 instruction cycles
1 cycle of each
1024 Clock Cycles (OST)
1024 Clock Cycles (OST) + 2 ms
1 s (approx.)
I/O
EXTERNAL CLOCK (EC)
MODE OPERATION
 2010 Microchip Technology Inc.
Oscillator Delay
OSC1/CLKIN
OSC2/CLKOUT
Mode”).
Overview”.
PIC
®
Table
MCU
Section 2.10
(1)
2-2.
WARM
)