AD1871YRS Analog Devices Inc, AD1871YRS Datasheet - Page 12

• Manufacturer Part Number: AD1871YRS
• Description: IC ADC STEREO AUDIO 24BIT 28SSOP
• Manufacturer: Analog Devices Inc

Specifications of AD1871YRS

• Rohs Status: RoHS non-compliant
• Number Of Bits: 24
• Sampling Rate (per Second): 96k
• Data Interface: Serial, SPI™
• Number Of Converters: 2
• Voltage Supply Source: Analog and Digital
• Operating Temperature: -40°C ~ 105°C
• Mounting Type: Surface Mount
• Package / Case: 28-SSOP (0.200", 5.30mm Width)

TERMINOLOGY
Dynamic Range
The ratio of a full-scale input signal to the integrated input
noise in the pass band (20 Hz to 20 kHz), expressed in decibels
(dB). Dynamic range is measured with a –60 dB input signal
and is equal to (S/[THD+N]) + 60 dB. Note that spurious
harmonics are below the noise with a –60 dB input, so the
noise level establishes the dynamic range. The dynamic range
is specified with and without an A-Weight filter applied.
Signal to (Total Harmonic Distortion + Noise)
(S/[THD+N])
The ratio of the root-mean-square (rms) value of the fundamen-
tal input signal to the rms sum of all other spectral components
in the pass band, expressed in decibels (dB).
Pass Band
The region of the frequency spectrum unaffected by the attenu-
ation of the digital decimator’s filter.
Pass-Band Ripple
The peak-to-peak variation in amplitude response from equal-
amplitude input signal frequencies within the pass band, expressed
in decibels.
Stop Band
The region of the frequency spectrum attenuated by the digital
decimator’s filter to the degree specified by stop-band attenuation.
Gain Error
With a near full-scale input, the ratio of the actual output to the
expected output, expressed as a percentage.
Interchannel Gain Mismatch
With identical near full-scale inputs, the ratio of the outputs of
the two stereo channels, expressed in decibels.
Gain Drift
Change in response to a near full-scale input with a change in
temperature, expressed as parts-per-million (ppm) per ∞C.
AD1871
–12–
Crosstalk (EIAJ Method)
Ratio of response on one channel with a grounded input to a
full-scale 1 kHz sine-wave input on the other channel, expressed
in decibels.
Power Supply Rejection
With no analog input, signal present at the output when a
300 mV p-p signal is applied to power supply pins, expressed in
decibels of full scale.
Group Delay
Intuitively, the time interval required for an input pulse to
appear at the converter’s output, expressed in milliseconds (ms).
More precisely, the derivative of radian phase with respect to
radian frequency at a given frequency.
GLOSSARY
ADC—Analog-to-Digital Converter
DSP—Digital Signal Processor
IMCLK—Internal master clock signal, used to clock the deci-
mating filter section. (Its frequency must be 256 ¥ f
MCLK—External master clock signal applied to the AD1871.
Its frequency can be 256, 512, or 768 ¥ f
internally to give an IMCLK frequency that must be 256 ¥ f
MODCLK—This is the - modulator clock that determines
the sample rate of the modulator. Ideally, it should not exceed
the lower of 6.144 MHz or 128 ¥ f
from the IMCLK by a divider that can be selected as /2 or /4.
MUX—Multiplexer
PGA—Programmable Gain Amplifier
S
. The MODCLK is derived
S
. MCLK is divided
S.
)
REV. 0
S
.