TMPM330FWFG Toshiba, TMPM330FWFG Datasheet - Page 448

• Manufacturer Part Number: TMPM330FWFG
• Description: Microcontrollers (MCU) MCU w/ ARM Cortex-M3 128K FLASH, 8K SRAM
• Manufacturer: Toshiba

Specifications of TMPM330FWFG

• Processor Series: TX03
• Core: ARM Cortex M3
• 3rd Party Development Tools: MDK-ARM, RL-ARM, ULINK2
• Product Summaries: Summary
• Lead Free: Yes
• Rohs Compatible Product(s): Available
• Rom (kbytes): 128K
• Rom Type: Flash
• Ram (kbytes): 8K
• Number Of Pins: 100
• Package: LQFP(14×14)
• Vcc: 3V
• Cpu Mhz: 40
• Ssp (ch) Spi: -
• I2c/sio (ch): 3
• Uart/sio (ch): 3
• Usb: -
• Can: -
• Ethernet: -
• External Bus Interface: -
• Cs/wait Controller (ch): -
• Dma Controller: -
• 10-bit Da Converter: -
• 10-bit Ad Converter: 12
• 12-bit Ad Converter: -
• 16-bit Timer / Counter: 10
• Motor / Igbt Control: -
• Real Time Clock: 1
• Watchdog Timer: Y
• Osc Freq Detect: -
• Clock Gear: Y
• Low-power Hold Function: -
• Remote Control Interface: Y
• Hardware Cec Controller: Y
• Comparators: -
• Low-voltage Detector: -
• Etm Hardware Trace: 4-bit
• Lead Free Status / Rohs Status: Details

17.2
Operation Mode
17.2.2
17.2.2.1
buses for flash memory program code on the old application and for serial I/O are different. It operates at the
single chip mode; therefore, a switch from normal mode in which user application is activated at the single chip
mode to User Boot Mode for programming flash is required. Specifically, add a mode judgment routine to a reset
program in the old application.
conformity with the user’s system setup condition. Also, flash memory programming routine that the user
uniquely makes up needs to be set in the new application. This routine is used for programming after being
switched to User Boot Mode. The execution of the programming routine must take place while it is stored in the
area other than the flash memory since the data in the internal flash memory cannot be read out during delete/
writing mode. Once re-programming is complete, it is recommended to protect relevant flash blocks from acci-
dental corruption during subsequent Single-Chip (Normal mode) operations. Be sure not to cause any exceptions
including a non-maskable while User Boot Mode.
memory. For a detailed description of the erase and program sequence, refer to "17.3 On-board Programming of
Flash Memory (Rewrite/Erase)".
User Boot mode is to use flash memory programming routine defined by users. It is used when the data transfer
The condition to switch the modes needs to be set by using the I/O of TMPM330FDFG/FYFG/FWFG in
(1-A) and (1-B) are the examples of programming with routines in the internal flash memory and in the external
User Boot Mode (Single chip mode)
(1)
(1-A) Method 1: Storing a Programming Routine in the Flash Memory
and the I/O bus to be used to transfer new program code. Create hardware and software accordingly.
Before installing the TMPM330FDFG/FYFG/FWFG on a printed circuit board, write the following
program routines into an arbitrary flash block using programming equipment.
Determine the conditions (e.g., pin states) required for the flash memory to enter User Boot mode
(a) Mode judgment routine:
(b) Programming routine:
(c) Copy routine:
Step-1
TMPM330FDFG/FYFG/FWFG
(a) Mode Judgment Routine
(b) Programming Routine
(c) Copy routine
Old Application
[Reset Procedure]
Program Code
Flash memory
Code to determine whether or not to switch to User Boot mode
Code to download new program code from a host controller and
re-program the flash memory
Code to copy the data described in (b) from the
TMPM330FDFG/FYFG/FWFG flash memory to either the
TMPM330FDFG/FYFG/FWFG on-chip RAM or external mem-
ory device.
Page 428
(I/O)
RAM
(Host)
New Application
Program Code
TMPM330FDFG/FYFG/FWFG