ATmega8515 Atmel Corporation, ATmega8515 Datasheet - Page 39

• Manufacturer Part Number: ATmega8515
• Manufacturer: Atmel Corporation

Specifications of ATmega8515

• Flash (kbytes): 8 Kbytes
• Pin Count: 44
• Max. Operating Frequency: 16 MHz
• Cpu: 8-bit AVR
• # Of Touch Channels: 16
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 35
• Ext Interrupts: 3
• Usb Speed: No
• Usb Interface: No
• Spi: 1
• Uart: 1
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Resistive Touch Screen: No
• Temp. Sensor: No
• Crypto Engine: No
• Sram (kbytes): 0.5
• Eeprom (bytes): 512
• Self Program Memory: YES
• Dram Memory: No
• Nand Interface: No
• Picopower: No
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 2.7 to 5.5
• Operating Voltage (vcc): 2.7 to 5.5
• Fpu: No
• Mpu / Mmu: no / no
• Timers: 2
• Output Compare Channels: 3
• Input Capture Channels: 1
• Pwm Channels: 3
• 32khz Rtc: No
• Calibrated Rc Oscillator: Yes

Calibrated Internal RC
Oscillator
Oscillator Calibration Register
– OSCCAL
2512K–AVR–01/10
The calibrated internal RC Oscillator provides a fixed 1.0, 2.0, 4.0, or 8.0 MHz clock. All
frequencies are nominal values at 5V and 25°C. This clock may be selected as the sys-
tem clock by programming the CKSEL Fuses as shown in Table 12. If selected, it will
operate with no external components. The CKOPT Fuse should always be unpro-
grammed when using this clock option. During reset, hardware loads the calibration byte
into the OSCCAL Register and thereby automatically calibrates the RC Oscillator. At 5V,
25°C, and 1.0 MHz Oscillator frequency selected, this calibration gives a frequency
within ± 3% of the nominal frequency. Using run-time calibration methods as described
in application notes available at www.atmel.com/avr it is possible to achieve ± 1% accu-
racy at any given V
the Watchdog Oscillator will still be used for the Watchdog Timer and for the Reset
Time-out. For more information on the pre-programmed calibration value, see the sec-
tion “Calibration Byte” on page 181.
Table 12. Internal Calibrated RC Oscillator Operating Modes
Note:
When this Oscillator is selected, start-up times are determined by the SUT Fuses as
shown in Table 13. XTAL1 and XTAL2 should be left unconnected (NC).
Table 13. Start-up Times for the Internal Calibrated RC Oscillator Clock Selection
Note:
• Bits 7..0 – CAL7..0: Oscillator Calibration Value
Writing the calibration byte to this address will trim the internal Oscillator to remove pro-
cess variations from the Oscillator frequency. During Reset, the 1 MHz calibrated value
which is located in the signature row High Byte (address 0x00) is automatically loaded
into the OSCCAL Register. If the internal RC is used at other frequencies, the calibration
values must be loaded manually. This can be done by first reading the signature row by
a programmer, and then store the calibration values in the Flash or EEPROM. Then the
value can be read by software and loaded into the OSCCAL Register. When OSCCAL is
zero, the lowest available frequency is chosen. Writing non-zero values to this register
Bit
Read/Write
Initial Value
SUT1..0
10
00
01
11
(1)
1. The device is shipped with this option selected.
1. The device is shipped with this option selected.
CAL7
Start-up Time from
R/W
7
CKSEL3..0
Power-down
0001
CC
0010
0011
0100
6 CK
6 CK
6 CK
and Temperature. When this Oscillator is used as the chip clock,
CAL6
R/W
(1)
6
CAL5
R/W
5
Device Specific Calibration Value
CAL4
Additional Delay from
R/W
4
Reset (V
Reserved
4.1 ms
65 ms
CAL3
R/W
3
CC
–
= 5.0V)
Nominal Frequency (MHz)
CAL2
R/W
2
ATmega8515(L)
CAL1
BOD enabled
Fast rising power
Slowly rising power
R/W
1.0
2.0
4.0
8.0
Recommended Usage
1
CAL0
R/W
0
OSCCAL
39