M30622ECTFP MITSUBISHI [Mitsubishi Electric Semiconductor], M30622ECTFP Datasheet - Page 52
M30622ECTFP
Manufacturer Part Number
M30622ECTFP
Description
SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER
Manufacturer
MITSUBISHI [Mitsubishi Electric Semiconductor]
Datasheet
1.M30622ECTFP.pdf
(184 pages)
- Current page: 52 of 184
- Download datasheet (2Mb)
Interrupt
Hardware Interrupts
Hardware interrupts are classified into two types — special interrupts and peripheral I/O interrupts.
(1) Special interrupts
(2) Peripheral I/O interrupts
• Reset
• NMI interrupt
• DBC interrupt
• Watchdog timer interrupt
• Single-step interrupt
• Address match interrupt
A peripheral I/O interrupt is generated by one of built-in peripheral functions. Built-in peripheral func-
tions are dependent on classes of products, so the interrupt factors too are dependent on classes of
products. The interrupt vector table is the same as the one for software interrupt numbers 0 through
31 the INT instruction uses. Peripheral I/O interrupts are maskable interrupts.
• Bus collision detection interrupt
• DMA0 interrupt, DMA1 interrupt
• Key-input interrupt
• A-D conversion interrupt
• UART0, UART1, UART2/NACK, SI/O3 and SI/O4 transmission interrupt
• UART0, UART1, UART2/ACK, SI/O3 and SI/O4 reception interrupt
• Timer A0 interrupt through timer A4 interrupt
• Timer B0 interrupt through timer B5 interrupt
• INT0 interrupt through INT5 interrupt
Tentative Specifications REV.A
Special interrupts are non-maskable interrupts.
Reset occurs if an “L” is input to the RESET pin.
_______
An NMI interrupt occurs if an “L” is input to the NMI pin.
This interrupt is exclusively for the debugger, do not use it in other circumstances.
Generated by the watchdog timer.
This interrupt is exclusively for the debugger, do not use it in other circumstances. With the debug
flag (D flag) set to “1”, a single-step interrupt occurs after one instruction is executed.
An address match interrupt occurs immediately before the instruction held in the address indicated by
the address match interrupt register is executed with the address match interrupt enable bit set to “1”.
If an address other than the first address of the instruction in the address match interrupt register is set,
no address match interrupt occurs. For address match interrupt, see 2.11 Address match Interrupt.
This is an interrupt that the serial I/O bus collision detection generates.
These are interrupts that DMA generates.
A key-input interrupt occurs if an “L” is input to the KI pin.
This is an interrupt that the A-D converter generates.
These are interrupts that the serial I/O transmission generates.
These are interrupts that the serial I/O reception generates.
These are interrupts that timer A generates
These are interrupts that timer B generates.
An INT interrupt occurs if either a rising edge or a falling edge or a both edge is input to the INT pin.
Note 1:
________
________
S
_______
______
pecifications in this manual are tentative and subject to change.
In M30623 (80-pin package), can not use INT
P1
5
/D
13
/INT
_______
3
to P1
________
7
/D
15
/INT
_______
____________
5
have no corresponding external pin.
52
_______
___
_______
3
to INT
_______
SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER
5
as the interrupt factors, because
Mitsubishi microcomputers
M16C / 62T Group
______
Related parts for M30622ECTFP
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
128 x 8-BIT x 2 MAIL-BOX
Manufacturer:
MITSUBISHI [Mitsubishi Electric Semiconductor]
Datasheet:
Part Number:
Description:
PROGRAMMABLE BUFFERED I/0 EXPANDER
Manufacturer:
MITSUBISHI [Mitsubishi Electric Semiconductor]
Datasheet:
Part Number:
Description:
ELECTRONIC SOUND CONTROL WITH ELECTRONIC VOLUME FOR MULTIPLE SOURCES
Manufacturer:
MITSUBISHI [Mitsubishi Electric Semiconductor]
Datasheet:
Part Number:
Description:
2CH 4 MODE PRESET EQUALIZER
Manufacturer:
MITSUBISHI [Mitsubishi Electric Semiconductor]
Datasheet:
Part Number:
Description:
SERIAL DATA CONTROL DUAL ELECTRONIC VOLUME
Manufacturer:
MITSUBISHI [Mitsubishi Electric Semiconductor]
Datasheet:
Part Number:
Description:
SCREEN CHARACTER and PATTERN DISPLAY CONTROLLERS?????
Manufacturer:
MITSUBISHI [Mitsubishi Electric Semiconductor]
Datasheet:
Part Number:
Description:
M51996P
Manufacturer:
MITSUBISHI [Mitsubishi Electric Semiconductor]
Datasheet:
Part Number:
Description:
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER??
Manufacturer:
MITSUBISHI [Mitsubishi Electric Semiconductor]
Datasheet:
Part Number:
Description:
SINGLE-CHIP 4-BIT CMOS MICROCOMPUTER
Manufacturer:
MITSUBISHI [Mitsubishi Electric Semiconductor]
Datasheet:
Part Number:
Description:
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
Manufacturer:
MITSUBISHI [Mitsubishi Electric Semiconductor]
Datasheet:
Part Number:
Description:
MITSUBISHI SEMICONDUCTOR (TRIAC) MEDIUM POWER USE INSULATED TYPE, PLANAR PASSIVATION TYPE
Manufacturer:
Mitsubishi Electric Semiconductor
Part Number:
Description:
MITSUBISHI SEMICONDUCTOR (TRIAC) LOW POWER USE GLASS PASSIVATION TYPE
Manufacturer:
Mitsubishi Electric Semiconductor
Part Number:
Description:
SINGLE-CHIP 4-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER with ON-SCREEN DISPLAY CONTROLLER?
Manufacturer:
MITSUBISHI [Mitsubishi Electric Semiconductor]
Datasheet:
Part Number:
Description:
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
Manufacturer:
MITSUBISHI [Mitsubishi Electric Semiconductor]
Datasheet:
Part Number:
Description:
SINGLE CHIP 8 BIT CMOS MICROCOMPUTER
Manufacturer:
MITSUBISHI [Mitsubishi Electric Semiconductor]
Datasheet: