M30622M4 MITSUBISHI [Mitsubishi Electric Semiconductor], M30622M4 Datasheet - Page 178
M30622M4
Manufacturer Part Number
M30622M4
Description
SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER
Manufacturer
MITSUBISHI [Mitsubishi Electric Semiconductor]
Datasheet
1.M30622M4.pdf
(276 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Part Number:
M30622M4A-462GP D3
Manufacturer:
RENESAS/瑞萨
Quantity:
20 000
- Current page: 178 of 276
- Download datasheet (4Mb)
Usage precaution
178
Noise
(4) External interrupt
(5) Rewrite the interrupt control register
(1) V
(2) Insert bypass capacitor between V
Note 1: Inserting a 5 K ohm resistor will not cause any problem when switching to mask ROM version.
PP
• When the polarity of the INT0 to INT5 pins is changed, the interrupt request bit is sometimes set
• To rewrite the interrupt control register, do so at a point that does not generate the interrupt
• When a instruction to rewrite the interrupt control register is executed but the interrupt is disabled,
• V
• Insert bypass capacitor (about 0.1 F) and connect short and wide line between V
to "1". After changing the polarity, set the interrupt request bit to "0".
request for that register. If there is possibility of the interrupt request occur, rewrite the interrupt
control register after the interrupt is disabled. The program examples are described as follow:
the interrupt request bit is not set sometimes even if the interrupt request for that register has
been generated. This will depend on the instruction. If this creates problems, use the below in-
structions to change the register.
Instructions : AND, OR, BCLR, BSET
with one-time PROM version or EPROM version. So CNV
ment of noise resistance. If CNV
resistor close to CNV
lines.
line of one-time PROM version or EPROM version
PP
Example 1:
Example 2:
Example 3:
The reason why two NOP instructions (four when using the HOLD function) or dummy read are inserted
before FSET I in Examples 1 and 2 is to prevent the interrupt enable flag I from being set before the
interrupt control register is rewritten due to effects of the instruction queue.
(This line is for PROM programming power line) line of internal PROM connected to CNV
INT_SWITCH1:
INT_SWITCH2:
INT_SWITCH3:
FCLR
AND.B
NOP
NOP
FSET
FCLR
AND.B
MOV.W MEM, R0
FSET
PUSHC FLG
FCLR
AND.B
POPC
I
#00h, 0055h ; Clear TA0IC int. priority level and int. request bit.
I
I
#00h, 0055h ; Clear TA0IC int. priority level and int. request bit.
I
I
#00h, 0055h ; Clear TA0IC int. priority level and int. request bit.
FLG
SS
pin and connect to V
_______
CC
; Disable interrupts.
; Four NOP instructions are required when using HOLD function.
; Enable interrupts.
; Disable interrupts.
; Dummy read.
; Enable interrupts.
; Push Flag register onto stack
; Disable interrupts.
; Enable interrupts.
_______
and V
SS
line is long, you should insert an approximately 5K ohm
SS
pin for noise and latch up countermeasure.
SS
or V
CC
.
SS
SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER
should be a short line for improve-
Mitsubishi microcomputers
M16C / 62 Group
CC
and V
SS
SS
Related parts for M30622M4
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
128 x 8-BIT x 2 MAIL-BOX
Manufacturer:
MITSUBISHI [Mitsubishi Electric Semiconductor]
Datasheet:
Part Number:
Description:
PROGRAMMABLE BUFFERED I/0 EXPANDER
Manufacturer:
MITSUBISHI [Mitsubishi Electric Semiconductor]
Datasheet:
Part Number:
Description:
ELECTRONIC SOUND CONTROL WITH ELECTRONIC VOLUME FOR MULTIPLE SOURCES
Manufacturer:
MITSUBISHI [Mitsubishi Electric Semiconductor]
Datasheet:
Part Number:
Description:
2CH 4 MODE PRESET EQUALIZER
Manufacturer:
MITSUBISHI [Mitsubishi Electric Semiconductor]
Datasheet:
Part Number:
Description:
SERIAL DATA CONTROL DUAL ELECTRONIC VOLUME
Manufacturer:
MITSUBISHI [Mitsubishi Electric Semiconductor]
Datasheet:
Part Number:
Description:
SCREEN CHARACTER and PATTERN DISPLAY CONTROLLERS?????
Manufacturer:
MITSUBISHI [Mitsubishi Electric Semiconductor]
Datasheet:
Part Number:
Description:
M51996P
Manufacturer:
MITSUBISHI [Mitsubishi Electric Semiconductor]
Datasheet:
Part Number:
Description:
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER??
Manufacturer:
MITSUBISHI [Mitsubishi Electric Semiconductor]
Datasheet:
Part Number:
Description:
SINGLE-CHIP 4-BIT CMOS MICROCOMPUTER
Manufacturer:
MITSUBISHI [Mitsubishi Electric Semiconductor]
Datasheet:
Part Number:
Description:
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
Manufacturer:
MITSUBISHI [Mitsubishi Electric Semiconductor]
Datasheet:
Part Number:
Description:
MITSUBISHI SEMICONDUCTOR (TRIAC) MEDIUM POWER USE INSULATED TYPE, PLANAR PASSIVATION TYPE
Manufacturer:
Mitsubishi Electric Semiconductor
Part Number:
Description:
MITSUBISHI SEMICONDUCTOR (TRIAC) LOW POWER USE GLASS PASSIVATION TYPE
Manufacturer:
Mitsubishi Electric Semiconductor
Part Number:
Description:
SINGLE-CHIP 4-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER with ON-SCREEN DISPLAY CONTROLLER?
Manufacturer:
MITSUBISHI [Mitsubishi Electric Semiconductor]
Datasheet:
Part Number:
Description:
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
Manufacturer:
MITSUBISHI [Mitsubishi Electric Semiconductor]
Datasheet:
Part Number:
Description:
SINGLE CHIP 8 BIT CMOS MICROCOMPUTER
Manufacturer:
MITSUBISHI [Mitsubishi Electric Semiconductor]
Datasheet: