dsPIC33FJ32MC104-I/PT Microchip Technology, dsPIC33FJ32MC104-I/PT Datasheet - Page 198

• Manufacturer Part Number: dsPIC33FJ32MC104-I/PT
• Description: Digital Signal Processors & Controllers - DSP, DSC 16bit Mtr Cnt Fam 16 MIPS 32KBFLSH 2KBRAM
• Manufacturer: Microchip Technology
• Type: dsPIC33FJ32(GP/MC)101/102/104r

Specifications of dsPIC33FJ32MC104-I/PT

• Rohs: yes
• Core: dsPIC33F
• Data Bus Width: 16 bit
• Program Memory Size: 32 KB
• Data Ram Size: 2 KB
• Maximum Clock Frequency: 7.37 MHz, 32 kHz
• Number Of Programmable I/os: 35
• Number Of Timers: 5 x 16-bit, 2 x 32-bit
• Device Million Instructions Per Second: 16 MIPs
• Operating Supply Voltage: 3 V to 3.6 V
• Maximum Operating Temperature: + 125 C
• Package / Case: TQFP-44
• Mounting Style: SMD/SMT
• Family / Core: dsPIC33FJ32(GP/MC)101/102/104
• Interface Type: I2C, SPI, UART
• Minimum Operating Temperature: - 40 C
• On-chip Adc: Yes
• Product: DSPs
• Program Memory Type: Flash
• Supply Current: 10 mA

dsPIC33FJ16(GP/MC)101/102 AND dsPIC33FJ32(GP/MC)101/102/104
REGISTER 16-2:
DS70652E-page 198
bit 15
bit 7
Legend:
R = Readable bit
-n = Value at POR
bit 15-13
bit 12
bit 11
bit 10
bit 9
bit 8
bit 7
bit 6
bit 5
Note 1:
SSEN
R/W-0
U-0
—
2:
3:
(2)
The CKE bit is not used in the Framed SPI modes. Program this bit to ‘0’ for the Framed SPI modes
(FRMEN = 1).
This bit must be cleared when FRMEN = 1.
Do not set both primary and secondary prescalers to a value of 1:1.
Unimplemented: Read as ‘0’
DISSCK: Disable SCKx pin bit (SPI Master modes only)
1 = Internal SPI clock is disabled, pin functions as I/O
0 = Internal SPI clock is enabled
DISSDO: Disable SDOx pin bit
1 = SDOx pin is not used by module; pin functions as I/O
0 = SDOx pin is controlled by the module
MODE16: Word/Byte Communication Select bit
1 = Communication is word-wide (16 bits)
0 = Communication is byte-wide (8 bits)
SMP: SPIx Data Input Sample Phase bit
Master mode:
1 = Input data sampled at end of data output time
0 = Input data sampled at middle of data output time
Slave mode:
SMP must be cleared when SPIx is used in Slave mode.
CKE: Clock Edge Select bit
1 = Serial output data changes on transition from active clock state to Idle clock state (see bit 6)
0 = Serial output data changes on transition from Idle clock state to active clock state (see bit 6)
SSEN: SPIx Slave Select Enable bit (Slave mode)
1 = SSx pin is used for Slave mode
0 = SSx pin is not used by module, pin is controlled by port function
CKP: Clock Polarity Select bit
1 = Idle state for clock is a high level; active state is a low level
0 = Idle state for clock is a low level; active state is a high level
MSTEN: Master Mode Enable bit
1 = Master mode
0 = Slave mode
R/W-0
CKP
U-0
—
SPI
X
CON1: SPIx CONTROL REGISTER 1
W = Writable bit
‘1’ = Bit is set
MSTEN
R/W-0
U-0
—
(1)
DISSCK
R/W-0
R/W-0
SPRE<2:0>
U = Unimplemented bit, read as ‘0’
‘0’ = Bit is cleared
DISSDO
R/W-0
R/W-0
(2)
(3)
MODE16
R/W-0
R/W-0
 2011-2012 Microchip Technology Inc.
x = Bit is unknown
R/W-0
R/W-0
SMP
PPRE<1:0>
CKE
R/W-0
R/W-0
(3)
(1)
bit 8
bit 0